Queclink GL300W

Features Queclink GL300W:

Blackbox

Supported in Wialon:

Remote management via GPRS
Remote management via SMS
Communication via TCP

The following data should also be added to Queclink GL300W unit properties section of Wialon GPS tracking software:

Device type:	Queclink GL300W
Unique ID:	imei

Specify the following parameters in configuration software or configuration Queclink GL300W for use in Wialon Hosting:

Server port:

21478

272 units of Queclink GL300W device type are connected to Wialon Data Center. This represents 0.03% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
report	RESP BUFF ACK
buffer	0 - not buffered message 1 - buffered message	{0,1}
msg_type_name	Name of message type
report_name	GTXXX where XXX is name of message type
proto_ver	Protocol Version
name	Device Name
report_id	Report ID. For GEO: it indicates the ID of the Geo-Fence. For FRI: it indicates the <Append Mask>. For SOS: 0: Triggered through other ways. 1: Triggered by input ID 1. For HBM: “3” indicates high speed, “2” indicates medium speed “1” indicates low speed.
report_type	Report Type. For FRI 0: This message is a common scheduled position report. 1: This message is a turning point. For GEO 0: Exit the corresponding Geo-fence. 1: Enter the corresponding Geo-fence. For SPD 0: Outside the speed range. 1: Inside the speed range. For NMR 0: The state of the device changes from motion to rest. 1: The state of the device changes from rest to motion. For DIS 0: The current logic status of the input port is low level. 1: The current logic status of the input port is high level. For IGL 0: The engine is ignition on. 1: The engine is ignition off. For DOG 0: Reboot periodically according to the <Interval> and <Time> settings or upon ignitionon or by <Input ID> 1: PDP is unable to register successfully or the interaction of messages fails 2: No WCDMA signal For HBM 0: Harsh braking behavior 1: Harsh acceleration behavior
mileage	Mileage
battery	Battery Percentage	0 - 100
temp	Temperature

Parameter name

Description

Units

report

RESP
BUFF
ACK

buffer

0 - not buffered message
1 - buffered message

{0,1}

msg_type_name

Name of message type

report_name

GTXXX where XXX is name of message type

proto_ver

Protocol Version

name

Device Name

report_id

Report ID.
For GEO:
it indicates the ID of the Geo-Fence.
For FRI:
it indicates the <Append Mask>.
For SOS:
0: Triggered through other ways.
1: Triggered by input ID 1.
For HBM:
“3” indicates high speed,
“2” indicates medium speed
“1” indicates low speed.

report_type

Report Type.
For FRI
0: This message is a common scheduled position report.
1: This message is a turning point.
For GEO
0: Exit the corresponding Geo-fence.
1: Enter the corresponding Geo-fence.
For SPD
0: Outside the speed range.
1: Inside the speed range.
For NMR
0: The state of the device changes from motion to rest.
1: The state of the device changes from rest to motion.
For DIS
0: The current logic status of the input port is low level.
1: The current logic status of the input port is high level.
For IGL
0: The engine is ignition on.
1: The engine is ignition off.
For DOG
0: Reboot periodically according to the <Interval> and <Time> settings or upon ignitionon or by <Input ID>
1: PDP is unable to register successfully or the interaction of messages fails
2: No WCDMA signal
For HBM
0: Harsh braking behavior
1: Harsh acceleration behavior

mileage

Mileage

battery

Battery Percentage

0 - 100

temp

Temperature

Gurtam products

Niche products for addressing specific tasks

Queclink GL300W

More devices from the manufacturer

News