Topflytech SolarGuardX 100

Topflytech SolarGuardX 100
Forum Discussion

Number of units

3
Online
11
Total
Features Topflytech SolarGuardX 100:
  • 4G/LTE
  • Blackbox
  • BLE enabled
  • E-seal
  • GLONASS support

The following data should also be added to Topflytech SolarGuardX 100 unit properties section of Wialon GPS tracking software :

Device type: Topflytech SolarGuardX 100
Unique ID: imei

Specify the following parameters in configuration software or configuration Topflytech SolarGuardX 100 for use in Wialon Hosting :

Server port: 22273

11 units of Topflytech SolarGuardX 100 device type are connected to Wialon Data Center. This represents 0.02% of all Asset trackers connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name Description Units
mcu_model

MCU model

modem_ver Version Information (Modem)
modem_app

Version Information

(Modem APP)

hw_ver

Hardware Version

mcu_fw_ver MCU firmware Version
gnss_status

Bits 1-8

1. Bit8=0, realtime data; Bit8=1, history data

2. Bit7=0, LBS data; Bit7=1, GNSS data

3. Bit6=0, GNSS is in working mode. Bit6=1,GNSS is in sleeping mode

4. Bit5~Bit1, locked satellite count

alarm

Alarm Code

acc_z

Acceleration Value

g
acc_y

Acceleration Value

g
acc_x

Acceleration Value

g
battery_percent

Build in Battery Voltage

%
temp

Device Internal Temperature

front_light

Front Light Sensor Voltage

pwr_int

Internal Battery Voltage

solar_voltage

Solar Panel Voltage

odom

Odometer

m
status

Status Bits 1-16

1. Bit16= 1, USB cable connected(with power) Bit16 =0, USB cable disconnected(without power)

2. Bit15~Bit12 show 4 manager phone number set or not. (1=set, 0=not)

4. Bit 11~Bit5, Network signal strength. Range: 0~100

5. Bit4=1, solar panel is charging the battery Bit4=0, solar panel doesn't charge the battery

6. Bit3=1, ignition on (moving) Bit3=0, ignition off (standstill)

7. Bit2=1 (Xtra Yes) Bit2=0 (Xtra No)

8. Bit1=0, normal timer reporting (TLP1-LF, TLP1-SF & TLP1-P) Bit1=1, smartpower timer reporting (TLP1-LF, TLP1-SF & TLP1-P)

network_signal

Network Signal Strength

acc_on

Igniton ON Upload Interval(Second)

acc_off

Ignition OFF or Accdet=0 UploadInterval (Second)

angle

Angle Upload Interval

deg
distance

Distance Upload Interval

m
heart

Heartbeat

min
settings_status

Current Setting Status Informaiton(1) Bits 1-8

1. Bit8: lock SIM card setting status Bit8=1, locked Bit8=0, unlocked

2. Bit7: lock device setting status Bit7=1, locked Bit7=0, unlocked

3. Bit6: AGPS Ephemeris data download setting status Bit6=1, enable download Bit6=0, disable download

4. Bit5:G-sensor setting status Bit5=1 enable Bit5=0, disable

5. Bit4: front sensor setting status Bit4=1, enable Bit4=0, disable

6. Bit3: Device remove alarm setting status Bit3=1 enable Bit3=0, disable

7. Bit2: open case alarm setting status Bit2=1, enable Bit2=0, disable

8.Bit1: device internal temperature reading and uploading setting status Bit1=1, enable Bit1=0, disable

network_operator

Network Operators Name

access_name

Access Technology Name

band_name

Band Name

imsi

SIM Card IMSI

iccid

ICCID

ign

ACC Status

1. 0x00 means ACC OFF

2. 0x01 means ACC ON

tps_#_pwr_int

Tire Presure Sensor Battery Voltage

V
tps_#_air_pres

Tire Pressure

kPa
tps_#_air_temp

Tire Air Temperature

ble_data_code

Tire Sensor ID

tps_#_status

Tire Pressure Data Status

ble_tag_id BLE Tag ID
ble_#_battery

BLE Tag Battery Voltage

V
ble_#_sos_type

BLE SOS Data Type

1. *=0, SOS alarm

2. *=1, Low battery alarm (lower than 2.4V)

ble_#_gnss_status

BLE Data and GNSS Status Bits 1-8

1. Bit8=0, realtime data; Bit8=1, history data

2. Bit7=0, LBS data; Bit7=1, GNSS data;

3. Bit6=0, GNSS is in working mode. Bit6=1, GNSS is in sleeping mode

4. Bit5~Bit1, locked satellite count

ble_#_driver_ident_type

BLE Driver Identification Data Type

ble_sens_id

BLE Temperature and Humidity Sensor ID

ble_#_pwr

Sensor Battery voltage

ble_#_pwr_p

Sensor Battery percentage

%
ble_#_temp

Temperature

ble_#_hmdt

Humidity

ble_#_light Ambient Light Status
ble_#_rssi

RSSI

ble_door_#

Door Status

ble_relay_#

Relay Status

ble_#_hum

Humidity

ble_#_air_press Air Pressure
ble_#_lux

Light Lux

ble_#_acc_x

Accel-X

ble_#_acc_y Accel-Y
ble_#_acc_z

Accel-Z

ble_#_status

Status Bits 1-8

Bit1 = 1, Door Opened

Bit2 = 1, Panic

Bit3 = 1, Impact

lock_status

Lock Status

Error: device lock or unlock mechanical failure;

Cleared: error status is cleared;

Failed: doesn't meet lock or unlock status;

Time out - after unlock done, if more than 60 seconds doesn't plug out rope, device will automatically lock;

0x00,Lock, lock status;

0x01,Rope cut;

0x03,Lock error, unlock status;

0x04,NFC wakes up device to connect network;

0x05,Unlock error, lock status;

0x06,Unlock error cleared,unlock status;

0x07,Lock error cleared,lock status;

0x08,Lock error cleared,unlock status;

0x11,NFC unlock successfully, unlock status;

0x12,NFC unlock successfully and plug out rope time out, lock status;

0x13,NFC unlock failed, out of built-in Geofence,lock status;

0x14,NFC unlock error, lock status;

0x15,NFC unlock successfully, wait for time out, unlock status;

0x16,Rope cut, NFC unlock error, rope cut and NFC unlock error;

0x21,Network unlock successfully, unlock status;

0x22,Network unlock successfully and plug out rope time out, lock status;

0x23,Network unlock failed, out of built-in Geofence,lock status;

0x24,Network unlock error, lock status;

0x25,Network unlock successfully, wait for time out, unlock status;

0x26,Rope cut, network unlock error, rope cut and network unlock error;;

0x31,BLE unlock successfully, unlock status;

0x32,BLE unlock successfully and plug out rope time out, lock status;

0x33,BLE unlock failed, out of built-in Geofence,lock status;

0x34,BLE unlock error, lock status;

0x35,BLE unlock successfully, wait for time out, unlock status;

0x36,Rope cut, BLE unlock error, rope cut and BLE unlock error;

0x41,SMS unlock successfully, unlock status;

0x42,SMS unlock successfully and plug out rope time out, lock status;

0x43,SMS unlock failed, out of built-in Geofence,lock status;

0x44,SMS unlock error, lock status;

0x45,SMS unlock successfully, wait for time out, unlock status;

0x46,Rope cut, SMS unlock error, rope cut and SMS unlock error;;

0x51,USB unlock successfully unlock status;

0x52,USB unlock successfullyl and plug out rope time out, lock status;

0x53,USB unlock failed, out of built-in Geofence,lock status;

0x54,USB unlock error, lock status;

0x55,USB unlock successfully, wait for time out, unlock status;

0x56,Rope cut, USB unlock error, rope cut and USB unlock error;



lock_data

NFC card (Hex format )ID or BLE APP unlock's smart phone's BLE MAC (Hex format) or SMS unlock's sender SIM card number(BCD (Binary-Coded Decimal‎)format)

More devices from the manufacturer

News

Contact Gurtam and achieve the most ambitious goals with telematics

Fill out a request form to get started with Wialon

Step 1
Step 2
Step 3
First and last name*
Company*
Email*
Phone