Jointech JT702

Jointech JT702
Manufacturer: Jointech
Forum Discussion

Number of units

0
Online
0
Total
Features Jointech JT702:
  • Blackbox
Supported in Wialon:
  • Remote management via GPRS
  • Communication via TCP

The following data should also be added to Jointech JT702 unit properties section of Wialon GPS tracking software:

Device type: Jointech JT702
Unique ID: custom

Specify the following parameters in configuration software or configuration Jointech JT702 for use in Wialon Hosting:

Server port: 21714

0 units of Jointech JT702 device type are connected to Wialon Data Center. This represents 0% of all Asset trackers connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name Description Units
gsm_signal GSM signal strength
mileage Mileage Km
power_status Power status,
0~100 means battery power level, eg 8%(unit: 0~ 100%),
0xFF means the device is not with battery,
0xAA means charging,
0xAB means powered by power supply.
cell_id Cell id
lac Lac id
product_type Product type
status Status, Bits 1-16
BIT16, BIT15, these two bit indicates the working mode change, Work to sleep is 1, sleep to work is 2
BIT6, lock status, 1 open, 0 lock
BIT5, Electronic lock status, 1 unlock, 0 lock
BIT4, front cover status, 1 damaged, 0 normal
BIT3, SIM card lid status, 1 lid opened, 2 closed normal
BIT2, low battery alarm, when the battery level less than 20%, 1 to notify, till the battery level higher than 20%, 0 means normal
alarm_bits Alarm Bits 1-16
BIT4, battery low power to sleep alarm, when the battery level is less than set value, it will fall asleep and can only be waken up by PA0
BIT3, when the vibration reach the set value, 1 is to alarm once, 0 indicates normal
BIT2, when enter low power working mode the value is 1, 0 means normal
gyro_x Gyro sensor X, Plus 180 degree, minus 180 degree
gyro_y Gyro sensor Y, Plus 90 degree, minus 90 degree
gyro_z Gyro sensor Z, Plus 180 degree, minus 180 degree
alarm_event Alarm event,
1 indicate remote fixed password,
2 indicate remote dynamic password
3 indicate dynamic password on site (Bluetooth orWIFI)APP
4 indicate dynamic password on site from keyboard
5 xxx
6 indicate wrong remote fixed password
7 indicate wrong remote dynamic password
8 indicate wrong dynamic password from on site (Bluetooth or WIFI)APP
9 indicate wrong dynamic password from keyboard,
10 xxx
11 indicate unlock overtime alert
12 Abnormal unlock alarm, abnormal unlock alarm, the lock has been作 opened abnormally, (Eg JT702 cable is cut) (When the device unlocked and the cable
13 lock remind didn’t pull out in 30 seconds, it will make noise to remind and then lock automatically).
14 SIM card lid open alarm, the lid open when the device is in locking status will be considered abnormal open.
15 Front cover tamper alarm, when the front cover damaged, the alarm will be generated. (For JT705 and JT706).
16 Unlock failed, the device cannot be unlocked, and not positioning.
17 Unlock failed, the device cannot be unlocked outside set geofence.
18 The electromagnet control is abnormal
19 The secondary board communication is abnormal
20\21\22\23 When the tilt angle in front back left right more than 45 degree and holds for 3 seconds, the tilting alarm will be triggered.


pass Password,
88888888:Normal unlock fixed or dynamic password, abnormal unlocking fixed or dynamic password.
carry_unlock_cmd Carry on the unlock command,
This parameter is only available when the password input correctly and unlocked
1 indicate unlock normally: The geofence area unlock function is not activated. 2 indicate unlock normally; The geofence area unlock function activated, the device is unlocked inside the set Geofence.
3 indicate unlock normally: the geofence area unlock function is activated, unlock remotely and the device is not positioning.
vehicle_inf Vehicle information,
vehicle information displays only when the device unlocked successfully. If not the vehicle information not filled, will be displayed with 0 or not displaying.

More devices from the manufacturer

News

Fill out a request form to get started with Wialon

Step 1
Step 2
Step 3
First and last name*
Company*
Email*
Phone