axoLOCK

Features axoLOCK:

3G
4G/LTE
Blackbox
E-seal

Supported in Wialon:

Remote management via GPRS
SMS sending of data
Communication via TCP

The following data should also be added to axoLOCK unit properties section of Wialon GPS tracking software:

Device type:	axoLOCK
Unique ID:	serial

Specify the following parameters in configuration software or configuration axoLOCK for use in Wialon Hosting:

Server port:

21922

11 units of axoLOCK device type are connected to Wialon Data Center. This represents 0.03% of all Asset trackers connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
mod28_entries	Module 28: Number of entries
mod28_e_category	Module 28: Event Category (2 Bytes)
mod28_e_code	Module 28: Event Code (2 Bytes)
mod28_sc_event	Module 28: Source of event
mod28_oc_state	Module 28: Open/Close state. (0 = Close, 1 = Open)
mod40_event_cat	Event Category – 1 (Nano)
mod40_event_code	Event Code – 1 (Temperature measurements) Event Code – 2 (Humidity measurements)
mod40_meta_reason	Metadata TX Reason: 0 – Normal 1 – Start Charging 2 – Requested by Command
mod40_alert_status	Violation/Alert status. 0 – Within the limits 1 – Within the limits 2 – Violating (not in alert) a lower TH but alert is not yet declared 3 – Violating (not in alert) a upper TH but alert is not yet declared 4 – Alert for lower TH violation 5 – Alert for upper TH violation 6 – Violating while in alert the lower TH 7 – Violating while in alert the upper TH
mod40_retr_indication	Retransmission indication. 0 – Retransmission 1 – Not retransmission
mod40_charging_status	Charging Status. 0 – Not charging* 1 – Charging slow 2 – Charging fast 3 – Charger Fault/Charger thermal shutdown
mod40_after_charging	30 min after charging indication. 0 – Not during 30 minutes after charging* 1 – During 30 minutes after charging
mod40_meta_source	Source of measurement 0x00÷0x0F – MultiSense unit (according to place in the PL, whether occupied/enabled or not) 0xFB – BT Extender 0xFC – Guest MultiSense (not in the list) 0xFD – High accuracy or specialized sensors of the CelloTrack Nano 20 (for example: Accurate temperature sensor, pressure sensor, etc) 0xFE – MCU internal (temperature only) 0xFF – Reserved
mod40_meta_sample	Metadata Sampling rate (Seconds)
mod40_{upper/lower}_{hum/temp}_{mod40_meta_source}	Metadata Upper/Lower threshold
mod40_num_sample	Number of samples in the payload
mod40_{part_name}_{mod40_meta_source}	Humidity/Temperature reading

Parameter name

Description

Units

mod28_entries

Module 28: Number of entries

mod28_e_category

Module 28: Event Category (2 Bytes)

mod28_e_code

Module 28: Event Code (2 Bytes)

mod28_sc_event

Module 28: Source of event

mod28_oc_state

Module 28: Open/Close state. (0 = Close, 1 = Open)

mod40_event_cat

Event Category – 1 (Nano)

mod40_event_code

Event Code – 1 (Temperature measurements)
Event Code – 2 (Humidity measurements)

mod40_meta_reason

Metadata TX Reason:
0 – Normal
1 – Start Charging
2 – Requested by Command

mod40_alert_status

Violation/Alert status.
0 – Within the limits
1 – Within the limits
2 – Violating (not in alert) a lower TH but alert is not yet declared
3 – Violating (not in alert) a upper TH but alert is not yet declared
4 – Alert for lower TH violation
5 – Alert for upper TH violation
6 – Violating while in alert the lower TH
7 – Violating while in alert the upper TH

mod40_retr_indication

Retransmission indication.
0 – Retransmission
1 – Not retransmission

mod40_charging_status

Charging Status.
0 – Not charging*
1 – Charging slow
2 – Charging fast
3 – Charger Fault/Charger thermal shutdown

mod40_after_charging

30 min after charging indication.
0 – Not during 30 minutes after charging*
1 – During 30 minutes after charging

mod40_meta_source

Source of measurement
0x00÷0x0F – MultiSense unit (according to place in the PL, whether occupied/enabled or not)
0xFB – BT Extender
0xFC – Guest MultiSense (not in the list)
0xFD – High accuracy or specialized sensors of the CelloTrack Nano
20 (for example: Accurate temperature sensor, pressure sensor, etc)
0xFE – MCU internal (temperature only)
0xFF – Reserved

mod40_meta_sample

Metadata Sampling rate (Seconds)

mod40_{upper/lower}_{hum/temp}_{mod40_meta_source}

Metadata Upper/Lower threshold

mod40_num_sample

Number of samples in the payload

mod40_{part_name}_{mod40_meta_source}

Humidity/Temperature reading

Fill out a request form to get started with Wialon

Gurtam products

Niche products for addressing specific tasks

axoLOCK

Fill out a request form to get started with Wialon