| dev_type |
Queclink device type
*HEX mode only
|
|
| proto_ver |
Queclink protocol version
*HEX mode only
|
|
| fw_ver |
Firmware version
*HEX mode only
|
|
| battery |
Battery level, 0-100
|
|
| pwr_ext |
External power source voltage
|
|
| adc_mode |
Analog Input Mode
|
|
| adc1 |
Analog Input 1 voltage
|
|
| din_status |
Digital Input (bit mask)
|
|
| dout_status |
Digital Output (bit mask)
|
|
| motion_status |
|
|
| ibutton |
|
|
| ges_enabled |
|
|
| ges_mode |
|
|
| ges_radius |
|
|
| ges_dt |
|
|
| geo_area_type |
|
|
| geo_mask_group |
|
|
| geo_area_mask_group_1 |
|
|
| geo_area_mask_group_2 |
|
|
| jamming_cw |
|
|
| jamming_gps |
|
|
| upc_cmd_id |
|
|
| upc_result |
|
|
| url |
|
|
| x_forward |
|
|
| y_forward |
|
|
| z_forward |
|
|
| x_side |
|
|
| y_side |
|
|
| z_side |
|
|
| x_vert |
|
|
| y_vert |
|
|
| z_vert |
|
|
| onewire[i]_id |
|
|
| onewire[i]_type |
|
|
| onewire[i]_data |
|
|
| fuel_sensor[i]_type |
|
|
| fuel_sensor[i]_id |
|
|
| fuel_sensor[i]_percent |
|
|
| fuel_sensor[i]_volume |
|
|
| pwr_int |
|
|
| jamming_status |
|
|
| crash_counter |
|
|
| upd_code |
|
|
| upd_retry |
|
|
| idle_dt |
|
|
| gps_signal_status |
|
|
| wave1_out_id |
|
|
| wave1_out_active |
|
|
| temp_alarm_id |
|
|
| temp_status |
|
|
| temp_device_id |
|
|
| temp_device_data |
|
|
| roaming_state |
|
|
| curr_mileage |
Current Trip Mileage
*HEX mode only
|
|
| total_mileage |
Total Mileage
*HEX mode only
|
|
| curr_hourmetercount |
Current Trip Hour Meter Count (accumulative ignition time)
*HEX mode only
|
|
| total_hourmetercount |
Total Hour Meter Count (accumulative ignition time)
*HEX mode only
|
|
| hw_ver |
|
|
| mcu_ver |
|
|
| fri_discard_no_fix |
|
|
| resp_report_mask |
|
|
| ign_dt |
|
|
| igf_dt |
|
|
| bat_status |
|
|
| iccid |
|
|
| csq_ber |
CSQ BER,0-7/99
|
|
| daylight_saving |
|
|
| time_zone |
|
|
| tcp_cmd_count |
|
|
| udp_cmd_count |
|
|
| sms_cmd_count_white |
|
|
| sms_cmd_count |
|
|
| tcp_msg_count |
|
|
| udp_msg_count |
|
|
| sms_msg_count_white |
|
|
| sms_msg_count |
|
|
| gir_trigger |
|
|
| mnc[i] |
Mobile network code. It is 3 digits in length and ranges from 000–999.
|
|
| lac[i] |
Location area code in hex format.
|
|
| cell_id[i] |
Cell ID in hex format.
|
|
| gps_level |
|
|
| jamming_indicator |
|
|
| sat_[sv_id] |
|
|
| ledon |
- 1 - Cell LED anf GNSS LED turn on as configured
- 2 - Both LEDs work 10 minutes after tge device is powered on and then will be off.
|
|
| charging |
Wheter the backup battery is charging when the main power supply is connected |
|
| pwr_s |
whether the external power supply is connected. |
|
| csq_rssi |
the level of signal strength |
|
| id |
The ID which is currently read |
|
| id_reptype |
- The ID is unauthorized or the ID authorization (IDA) function is disabled;
- The ID is authorized
|
|
| indx |
- The index of Bluetooth accessory defined in AT+GTBAS which triggers the +RESP:GTBAA message
- 0xFF for WKF300
|
|
| acces_type |
- 0 - No bluetooth accessory
- 1 - Reserved
- 2 - Beacon temperature sensor
- 3 - BLE beacon ID device
|
|
| acbe_model |
The model of the bluetooth accessory
|
|
| alarm_type |
- 0 - the voltage of the Bluetooth accessory is low
- 1 - the temperature alarm: current temperature value is below
- 2 - the temperature alarm: current temperature value is upper
- 3 - the temperature alarm: current temperature value is within the range defined by <low temperature> and <high temperature>
- 4 - Push button event on WKF300 is detected
|
|
| bt_name |
Bluetooth accessory name |
|
| bt_mac |
Bluetooth accessory mac |
|
| bt_status |
- 0 - the accessory is not available
- 1 - the accessory is available
|
|
| bt_bat_level |
The voltage of Bluetooth accessory |
|
| bt_temp |
Temperature data fo Bluetooth accessory |
|
| can_eng_torgue |
Engine Torgue |
|
| rep_id |
Report ID has different meanings in different messages as listed below.
- Position related packages (GTTOW, GTDIS, GTIOB, GTSPD, GTSOS, GTRTL, GTDOG, GTIGL,GTHBM, GTVGL)
- The ID of digital input port which triggers the message +RESP:GTSOS. The range is 1 – 2.
- The ID of the bound IO which triggers the message +RESP:GTIOB. The value is 0.
- The ID of the digital input port which triggers the reboot message +RESP:GTDOG. The valid value is 1.
- The speed level at which the harsh behavior is detected in the message +RESP:GTHBM. 3 indicates high speed, 2 indicates medium speed and 1 indicates low speed.
- The value of <Virtual Ignition Mode> which indicates the trigger source of the message +RESP:GTVGL.
2: External power voltage mode (virtual ignition detection)
3: Reserved
4: Accelerometer mode (virtual ignition detection)
7: Combined detection mode (virtual ignition detection) - The ID of Digital Input status which triggers the report message +RESP:GTDIS. The rangeis 1 or 2.
- For other messages, it will always be 0.
- GTFRI:
- 1: Fixed time report.
- 2: Fixed distance report.
- 3: Fixed mileage report.
- 4: Fixed time and mileage report.
- 5: Fixed time or mileage report.
- GTEPS\GTAIS:
- The ID of the analog input port which triggers the report message +RESP:GTEPS. The value is 0
- The ID of the analog input port which triggers the report message +RESP:GTAIS. The value is or 5.
- GTTMP:
- The ID of temperature alarm. The range is 0 – 3.
- GTHUM:
- The ID of humidity alarm. The range is 0 – 3.
- GTUDT
- GEO-Fence / PEO-Fence event triggered report ID. It is in HEX format.
|
|
| rep_type |
Report Type has different meanings in different messages: - Position related packages (GTTOW, GTDIS, GTIOB, GTSPD, GTSOS, GTRTL, GTDOG, GTIGL,GTHBM, GTVGL)
In the message +RESP:GTDIS generated by a digital input (0: The current logic status of the input port is Disable status; 1: The current logic status of the input is Enable status.) In the message +RESP:GTIOB generated by bound IO (0: The current logic status of the bound IO does not meet the alarm condition; 1: The current logic status of the bound IO meets the alarm condition.) In the speed alarm message +RESP:GTSPD (0: Outside the predefined speed range; 1: Inside the predefined speed range) In the protocol watchdog message +RESP:GTDOG (1: Reboot device message for time based working mode 2: Reboot device message for ignition on working mode 3: Reboot device message for input triggered 4: Reboot device message for network watchdog 5: Reboot device message for EGPRS/LTE watchdog 6: Reboot device message for send failure watchdog 7: Reboot RF message for network watchdog 8: Reboot RF message for EGPRS/LTE watchdog 9: Reboot RF message for send failure watchdog) In the harsh behavior monitoring message +RESP:GTHBM (0: Harsh braking behavior 1: Harsh acceleration behavior) In the (virtual) ignition on/off location messages +RESP:GTIGL and +RESP:GTVGL (0: Ignition on 1: Ignition off) For other messages, it will always be 0.
- GTFRI\GTERI:
- GTEPS\GTAIS:
- 0: Outside the predefined range.
- 1: Inside the predefined range.
- GTTMP:
- 0 means “Outside the predefined temperature range”.
- 1 means “Inside the predefined temperature range”.
- GTVGN:
- 2: External power voltage mode (virtual ignition detection)
- 4: Accelerometer mode (virtual ignition detection)
- 7: Combined detection mode
- GTGES:
- 0: The current Parking-Fence is inactive.
- 1: The current Parking-Fence is active.
- GTHUM:
- 0 means outside the predefined humidity range.
- 1 means inside the predefined humidity range.
- GTUDT:
- 0: Timer event triggered.
- 1: GEO-Fence event triggered.
- 2: PEO-Fence event triggered.
- GTDAT
- 1: Reserved
- 2: AT+GTDAT from Bluetooth
- 3: AT+GTDAT from over the air
- 4: AT+GTDAT triggered by events in AT+GTUDF
- GTCAN
0: Periodic report. 1: RTO CAN report 2: Ignition event report
|
|
| gnss_trigger_type |
The trigger type of GNSS point has the following meanings. 0: Time point
1: Corner point
2: Distance point
3: Mileage point
4: Optimum point (time & mileage)
|
|
| mileage |
The current total mileage.
|
|
