Localizador GPS de activos Topflytech TLW2-12B

Características Topflytech TLW2-12B:

Caja negra
BLE

Para que el sistema de rastreo Wialon identifique los datos de Topflytech TLW2-12B en el diálogo de configuración de la unidad, indique los siguientes datos:

Tipo de dispositivo:	Topflytech TLW2-12B
ID único:	custom

Indique los siguientes parámetros en el programa de configuración o en la configuración Topflytech TLW2-12B para utilizarlos en Wialon Hosting:

Puerto del servidor:

22095

En el centro de servicio Wialon se utilizan 735 unidades Topflytech TLW2-12B — es 1.7% de la cantidad total de dispositivos Rastreador de activos conectados.

La gráfica representa la cantidad de conexiones en el centro de servicio Wialon en los últimos 30 días:

Nombre del parámetro	Descripción	Unidades de medida
ign	Ignition state: 0 - off, 1 - on
battery	The current volume of the backup battery
call_number	The phone number of the incoming call
charging	Whether the backup battery is charging when the main power supply is connected. 0 - not charging 1 - charging
csq_ber	The quality of the GSM signal. The range is 0-99
curr_hour_meter	The current hour meter count
curr_mileage	The current mileage
data_type	The data reported to backend server is recorded before or after crash: 0 - before crash 1 - after crash
AGPS	Support AGPS
Engine Stop	Can connect relay to stop car’s engine
MIC	Inner Mic-phone for voice monitor
SOS	SOS button
Bluetooth	Bluetooth for 2 ways audio
ext_pow_supply	Whether the external power supply is connected. 0 - not connected 1 - connected
fuel_level_input	Indicates the nominal fuel tank liquid fill capacity as a percent of maximum
gps_acc	GPS accuracy
gps_signal	GPS signal status: 0 - lost GPS signal or no successful GPS fix 1 - GPS signal recovered and successful GPS fix
hard_ver	The hardware version
harsh_behavior	Harsh behavior
harsh_speed_level	The speed level of which the harsh behavior is detected
idling	The time that the vehicle has been in idling status
ign_off_duration	Duration since last time the ignition is off
ign_on_duration	Duration since last time the ignition is on
jamming_status	The current Jamming status of the device. 1 - quit the jamming 2 - enter the jamming
led_on	Whether the LED’s are turned on. 0 - off 1 - on
mil_activated_dist	The distance accumulated since MIL is activated
mileage	The total mileage
mil_status	Malfunction Indicator Lamp (MIL) status: 0 - off 1 - on
packet_type	Report packet type
pwr_ext	The voltage of the external power supply
pwr_int	The voltage of the backup battery. The value of this field is only valid when the external power is not connected.
soft_ver	The software version
state	The current motion state of device: Tow Fake Tow Ignition Off Rest Ignition Off Motion Ignition On Rest Ignition On Motion Sensor Rest Sensor Motion
throttle_pos	Indicates a percentage of throttle position sensor value. Usually above 0% at idle and less than 100% at full throttle.
time_zone	Time zone offset
x_axisN	The X axis acceleration
y_axisN	The Y axis acceleration
z_axisN	The Z axis acceleration
ign_on_interval	Ignition ON Upload Interval	sec
ign_off_interval	Ignition OFF Upload Interval	sec
angle_interval	Angle Upload Interval	°
distance_interval	Distance Upload Interval	m
overspeed	Over Speed Alarm Setting: Bit15=0, unit is KM/H; Bit15=1, unit is Mile/H; Value=0 (Bit14~ Bit7), over speed alarm disabled
rssi	Network signal strength
gps_data	Bit7=0, realtime data; Bit7=1, history data Bit6=0, LBS data; Bit6=1, GNSS data Bit5=0, GNSS is in working mode. Bit5=1, GNSS is in sleeping mode
gsensor_sens	Bit7~Bit4, total 16 different gsensor sensitivity for move.
manager_status	Bit3~Bit0, show 4 managers status (set or not) Value=1, manger is set; Value=0, manager is null
other	Bit7: lock SIM card; Value=1, locked; Value=0, unlocked Bit6: lock device; value=1, locked; value=0, unlocked Bit5 always =0, no specific meaning Bit4: antitheft alarm; value=1, enabled, value=0, disabled Bit3~Bit0 total 16 different vibration sensitivity for vribration alarm.
heartbeat	Heartbeat	min
relay_status	1. Bit7=1, device received the engine cut command 2. Bit7=0, device received the engine recover command 3. Bit6=1, engine cut OK 4. Bit6=0 enginee cut failed because gps not fix or speed more than 20KM/H; 5.Build in alarm SMS message language: Bit3~Bit0; value=0, Chinese value=1, English value=2, French value=3, Spanish value=4, German value=5, Portuguese value=6, Arabic value=7, Indonesian value=8, Russian value=9, Turkish
drag_alarm	Value(Bit15~Bit0)=0, the drag alarm is disabled
digital_io	1. Bit15: external power supply; value=0, external power is connected; value=1, external power is disconnected 2. Bit14: Ignition digtal input, value=1 igntion ON; value=0 ignition OFF 3. Bit13, AC digital input, value=1 AC on; value=0 AC off 4. Bit12,digital input 3, value=1, on; value=0, off 5. Bit 11, digital input 4; value=1, on; value=0, off 6. Bit 10, digital input 5; value=1, on; value=0, off 7. Bit 9, digital input 6; value=1, on; value=0, off 8. Bit0: ACCDET setting status, value=1, enabled; value=0, disabled
digital_out	1. Bit7: Vout, value=0, 5V output; value=1, 12V output 2. Bit6：Vout, value=0 (off); value=1 (on) 3. Bit5: digital output1, value=1 (on); value=0 (off) 4. Bit4: digital output2, value=1 (on); value=0 (off) 5. Bit3: digital output3, value=1 (on); value=0 (off)
adcN	Analog Inputs	V
alarm	1. Value=1, external power disconnected 2. Value=2, build in battery low power alarm 3. Value=3, SOS alarm 4. Value=4, over speed alarm 5. Value=5, into geofence alarm 6. Value=6, out of geofence alarm 7. Value=7, drag alarm 8. Value=8, vibration alarm 9. Value=9, device get address for postion SMS 10. Value=10, antitheft alarm 11. Value=11, analog input1 voltage increase alarm 12. Value=12, analog input1 voltage decrease alarm 13. Value=13, analog input2 voltage increase alarm 14. Value=14, analog input2 voltage decrease alarm 15. Value=15, ACC on alarm 16. Value=16, ACC off alarm 17. Value=17, AC on alarm 18. Value=18, AC off alarm 19. Value=19, one idling start alarm. Customer can define the idling timing 20. Value=20, one idling end alarm 21. Value=21, signal jammer start alarm. (config with JAMMERD command) 22. Value=22, signal jammer end alarm 23. Value=23, external power recover alarm 24. Value=24, alarm of the external power voltage lower than threshold value. (config with AEPOWER command) 25. Value=25, digital 3 input from 0 to 1; 26. Value=26, digital 3 input from 1 to 0; 27. Value=27, digital 4 input from 0 to 1; 28. Value=28, digital 4 input from 1 to 0; 25. Value=29, digital 5 input from 0 to 1; 26. Value=30, digital 5 input from 1 to 0; 27. Value=31, digital 6 input from 0 to 1; 28. Value=32, digital 6 input from 1 to 0; 29. Value=33, analog input3 voltage increase alarm 30. Value=34, analog input3 voltage decrease alarm 31. Value=35, analog input4 voltage increase alarm 32. Value=36, analog input4 voltage decrease alarm
reserve	Bit5: SMS alarm to manager phone number status. Value=0, send SMS alarm; value=1, not send SMS alarm; default is 0 Bit4: digital input2 status SMS alarm. Value=0, not send SMS alarm; value=1 send SMS alarm; default is 0# 1. Bit3 & Bit2=00, jammer detection is disabled; 2. Bit3 & Bit2=01, jammer detection is enabled. Only send jammer alarm after network recovered, doesn't cut the engine; 3. Bit3 & Bit2=11, jammer detection is enabled. When the jammer is detected, the alarm will be triggered and saved in the tracker. At the same time the engine will be cut. After the network recovered, the alarm will be sent out; 4. The alarm code is 21. It's in 0x250x250x04 byte38
odometer	Odometer	m
rpm	Revolutions Per Minites
smart_upload	Bit7：smart upload support Bit7=1, enable Bit7=0, disable Bit0: in smart upload or not Bit0 = 1: yes Bit0 = 0: no
battery_monitoring	Battery monitoring: bit15：always in 0, it stands for it's a rechargeable battery device bit14~bit0: When bit15=0，it stands for how long the device is in the low battery mode.
temp_int	Device Internal Temperature	℃

Nombre del parámetro

Descripción

Unidades de medida

ign

Ignition state: 0 - off, 1 - on

battery

The current volume of the backup battery

call_number

The phone number of the incoming call

charging

Whether the backup battery is charging when the main power supply is connected.
0 - not charging
1 - charging

csq_ber

The quality of the GSM signal. The range is 0-99

curr_hour_meter

The current hour meter count

curr_mileage

The current mileage

data_type

The data reported to backend server is recorded before or after crash:
0 - before crash
1 - after crash

AGPS

Support AGPS

Engine Stop

Can connect relay to stop car’s engine

MIC

Inner Mic-phone for voice monitor

SOS

SOS button

Bluetooth

Bluetooth for 2 ways audio

ext_pow_supply

Whether the external power supply is connected.
0 - not connected
1 - connected

fuel_level_input

Indicates the nominal fuel tank liquid fill capacity as a percent of maximum

gps_acc

GPS accuracy

gps_signal

GPS signal status:
0 - lost GPS signal or no successful GPS fix
1 - GPS signal recovered and successful GPS fix

hard_ver

The hardware version

harsh_behavior

Harsh behavior

harsh_speed_level

The speed level of which the harsh behavior is detected

idling

The time that the vehicle has been in idling status

ign_off_duration

Duration since last time the ignition is off

ign_on_duration

Duration since last time the ignition is on

jamming_status

The current Jamming status of the device.
1 - quit the jamming
2 - enter the jamming

led_on

Whether the LED’s are turned on.
0 - off
1 - on

mil_activated_dist

The distance accumulated since MIL is activated

mileage

The total mileage

mil_status

Malfunction Indicator Lamp (MIL) status:
0 - off
1 - on

packet_type

Report packet type

pwr_ext

The voltage of the external power supply

pwr_int

The voltage of the backup battery. The value of this field is only valid when the external power is not connected.

soft_ver

The software version

state

The current motion state of device:

Tow
Fake Tow
Ignition Off Rest
Ignition Off Motion
Ignition On Rest
Ignition On Motion
Sensor Rest
Sensor Motion

throttle_pos

Indicates a percentage of throttle position sensor value. Usually above 0% at idle and less than 100% at full throttle.

time_zone

Time zone offset

x_axisN

The X axis acceleration

y_axisN

The Y axis acceleration

z_axisN

The Z axis acceleration

ign_on_interval

Ignition ON Upload Interval

sec

ign_off_interval

Ignition OFF Upload Interval

sec

angle_interval

Angle Upload Interval

distance_interval

Distance Upload Interval

overspeed

Over Speed Alarm Setting:

Bit15=0, unit is KM/H; Bit15=1, unit is Mile/H;

Value=0 (Bit14~ Bit7), over speed alarm disabled

rssi

Network signal strength

gps_data

Bit7=0, realtime data; Bit7=1, history data

Bit6=0, LBS data; Bit6=1, GNSS data

Bit5=0, GNSS is in working mode. Bit5=1, GNSS is in sleeping mode

gsensor_sens

Bit7~Bit4, total 16 different gsensor sensitivity for move.

manager_status

Bit3~Bit0, show 4 managers status (set or not)

Value=1, manger is set; Value=0, manager is null

other

Bit7: lock SIM card; Value=1, locked; Value=0, unlocked

Bit6: lock device; value=1, locked; value=0, unlocked

Bit5 always =0, no specific meaning

Bit4: antitheft alarm; value=1, enabled, value=0, disabled

Bit3~Bit0 total 16 different vibration sensitivity for vribration alarm.

heartbeat

Heartbeat

min

relay_status

1. Bit7=1, device received the engine cut command

2. Bit7=0, device received the engine recover command

3. Bit6=1, engine cut OK

4. Bit6=0 enginee cut failed because gps not fix or speed more than 20KM/H;

5.Build in alarm SMS message language: Bit3~Bit0; value=0, Chinese

value=1, English

value=2, French

value=3, Spanish

value=4, German

value=5, Portuguese

value=6, Arabic

value=7, Indonesian

value=8, Russian

value=9, Turkish

drag_alarm

Value(Bit15~Bit0)=0, the drag alarm is disabled

digital_io

1. Bit15: external power supply; value=0, external power is connected; value=1, external power is disconnected

2. Bit14: Ignition digtal input, value=1 igntion ON; value=0 ignition OFF

3. Bit13, AC digital input, value=1 AC on; value=0 AC off

4. Bit12,digital input 3, value=1, on; value=0, off

5. Bit 11, digital input 4; value=1, on; value=0, off

6. Bit 10, digital input 5; value=1, on; value=0, off

7. Bit 9, digital input 6; value=1, on; value=0, off

8. Bit0: ACCDET setting status, value=1, enabled; value=0, disabled

digital_out

1. Bit7: Vout, value=0, 5V output; value=1, 12V output

2. Bit6：Vout, value=0 (off); value=1 (on)

3. Bit5: digital output1, value=1 (on); value=0 (off)

4. Bit4: digital output2, value=1 (on); value=0 (off)

5. Bit3: digital output3, value=1 (on); value=0 (off)

adcN

Analog Inputs

alarm

1. Value=1, external power disconnected

2. Value=2, build in battery low power alarm

3. Value=3, SOS alarm

4. Value=4, over speed alarm

5. Value=5, into geofence alarm

6. Value=6, out of geofence alarm

7. Value=7, drag alarm

8. Value=8, vibration alarm

9. Value=9, device get address for postion SMS

10. Value=10, antitheft alarm

11. Value=11, analog input1 voltage increase alarm

12. Value=12, analog input1 voltage decrease alarm

13. Value=13, analog input2 voltage increase alarm

14. Value=14, analog input2 voltage decrease alarm

15. Value=15, ACC on alarm

16. Value=16, ACC off alarm

17. Value=17, AC on alarm

18. Value=18, AC off alarm

19. Value=19, one idling start alarm. Customer can define the idling timing

20. Value=20, one idling end alarm

21. Value=21, signal jammer start alarm. (config with JAMMERD command)

22. Value=22, signal jammer end alarm

23. Value=23, external power recover alarm

24. Value=24, alarm of the external power voltage lower than threshold value. (config with AEPOWER command)

25. Value=25, digital 3 input from 0 to 1;

26. Value=26, digital 3 input from 1 to 0;

27. Value=27, digital 4 input from 0 to 1;

28. Value=28, digital 4 input from 1 to 0;

25. Value=29, digital 5 input from 0 to 1;

26. Value=30, digital 5 input from 1 to 0;

27. Value=31, digital 6 input from 0 to 1;

28. Value=32, digital 6 input from 1 to 0;

29. Value=33, analog input3 voltage increase alarm

30. Value=34, analog input3 voltage decrease alarm

31. Value=35, analog input4 voltage increase alarm

32. Value=36, analog input4 voltage decrease alarm

reserve

Bit5: SMS alarm to manager phone number status. Value=0, send SMS alarm; value=1, not send SMS alarm; default is 0

Bit4: digital input2 status SMS alarm. Value=0, not send SMS alarm; value=1 send SMS alarm; default is 0#

1. Bit3 & Bit2=00, jammer detection is disabled;

2. Bit3 & Bit2=01, jammer detection is enabled. Only send jammer alarm after network recovered, doesn't cut the engine;

3. Bit3 & Bit2=11, jammer detection is enabled. When the jammer is detected, the alarm will be triggered and saved in the tracker. At the same time the engine will be cut. After the network recovered, the alarm will be sent out;

4. The alarm code is 21. It's in 0x250x250x04 byte38

odometer

Odometer

rpm

Revolutions Per Minites

smart_upload

Bit7：smart upload support

Bit7=1, enable

Bit7=0, disable

Bit0: in smart upload or not

Bit0 = 1: yes

Bit0 = 0: no