Asset GPS tracker Seeworld W18l | Integrated with Wialon

Features Seeworld W18l:

4G/LTE
Wi-Fi positioning

Supported in Wialon:

Remote management via GPRS
LBS
Communication via TCP

The following data should also be added to Seeworld W18l unit properties section of Wialon GPS tracking software :

Device type:	Seeworld W18l
Unique ID:	custom

Specify the following parameters in configuration software or configuration Seeworld W18l for use in Wialon Hosting :

Server port:

22615

56 units of Seeworld W18l device type are connected to Wialon Data Center. This represents 0.03% of all Asset trackers connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
alarm_status	Alarm status: 0: Normal 1: Shock Alarm 2: Power Cut Alarm 3: Low Battery Alarm 4: SOS
mcc	Mobile Country Code
mnc	Mobile Network Code
lac	Location Area Code
cell_id	Cell Tower ID
volt_lvl	The arrange is 0~6 defining the voltage is from low to high. 0: No Power (shutdown) 1: Extremely Low Battery (not enough for calling or sending text messages, etc.) 2: Very Low Battery (Low Battery Alarm) 3: Low Battery (can be used normally) 4: Medium 5: High 6: Very High
gsm	GSM signal strength degree
pwr_ext	External voltage	V
lang	Language. ch: Chinese en: English
term_info	1 byte that represents the status information of the terminal. One byte is regarded as 8 bits, the lowest bit is 0 bits, and the highest bit is 7 bits. Bit 7 1: Oil and electricity disconnected 0: Oil and electricity connected Bit 6 1: GPS has positioned 0: GPS not positioned Bit 5- Bit 3 111: Door open alarm 110: Door closing alarm 100: SOS alarm 011: Low battery alarm 010: Power failure alarm 001: Vibration alarm 000: normal Bit 2 1: Connected to external power supply 0: No external power supply connected Bit 1 1: ACC ON 0: ACC OFF Bit 0 1: Fortification 0: Disarm
travel_time	Total travel time in seconds	sec
temp	Temperature	Celsius
humidity	Humidity	%RH
data_mode	Data reporting mode. 0x00: Regular reporting 0x01: Fixed interval reporting 0x02: Inflection point upload 0x03: ACC status change upload 0x04: After changing from motion to static state, the last positioning point is transmitted. 0x05: After the network is disconnected and reconnected, the last valid upload point before reporting 0x06: Reporting mode: Mandatory upload of GPS points for ephemeris update 0x07: Reporting mode: press the button to upload the anchor point 0x08: Reporting mode: report location information after power on 0x09: Reporting mode: not used 0x0A : Reporting mode: the device reports the last longitude and latitude after being stationary, but the time is updated 0x0B : WIFI parsing longitude and latitude upload package 0x0C : Reporting mode: LJDW (immediate positioning) command reporting 0x0D : Reporting mode: report the last longitude and latitude after the device is stationary 0x0E : Reporting mode: GPSDUP upload (scheduled upload in static state)

Parameter name

Description

Units

alarm_status

Alarm status:
0: Normal
1: Shock Alarm
2: Power Cut Alarm
3: Low Battery Alarm
4: SOS

mcc

Mobile Country Code

mnc

Mobile Network Code

lac

Location Area Code

cell_id

Cell Tower ID

volt_lvl

The arrange is 0~6 defining the voltage is from low to high.

0: No Power (shutdown)

1: Extremely Low Battery (not enough for calling or sending text messages, etc.)

2: Very Low Battery (Low Battery Alarm)

3: Low Battery (can be used normally)

4: Medium

5: High

6: Very High

gsm

GSM signal strength degree

pwr_ext

External voltage

lang

Language.

ch: Chinese

en: English

term_info

1 byte that represents the status information of the terminal. One byte is regarded as 8 bits, the lowest bit is 0 bits, and the highest bit is 7 bits.

Bit 7

1: Oil and electricity disconnected
0: Oil and electricity connected

Bit 6

1: GPS has positioned
0: GPS not positioned

Bit 5- Bit 3

111: Door open alarm
110: Door closing alarm
100: SOS alarm
011: Low battery alarm
010: Power failure alarm
001: Vibration alarm
000: normal

Bit 2

1: Connected to external power supply
0: No external power supply connected

Bit 1

1: ACC ON
0: ACC OFF

Bit 0

1: Fortification
0: Disarm

travel_time

Total travel time in seconds

sec

temp

Temperature

Celsius

humidity

Humidity

%RH

data_mode

Data reporting mode.

0x00: Regular reporting
0x01: Fixed interval reporting
0x02: Inflection point upload
0x03: ACC status change upload
0x04: After changing from motion to static state, the last positioning point is transmitted.
0x05: After the network is disconnected and reconnected, the last valid upload point before reporting
0x06: Reporting mode: Mandatory upload of GPS points for ephemeris update
0x07: Reporting mode: press the button to upload the anchor point
0x08: Reporting mode: report location information after power on
0x09: Reporting mode: not used
0x0A : Reporting mode: the device reports the last longitude and latitude after being stationary, but the time is updated
0x0B : WIFI parsing longitude and latitude upload package
0x0C : Reporting mode: LJDW (immediate positioning) command reporting
0x0D : Reporting mode: report the last longitude and latitude after the device is stationary
0x0E : Reporting mode: GPSDUP upload (scheduled upload in static state)

Fill out a request form to get started with Wialon

Products

Niche products for addressing specific tasks

Seeworld W18l

More devices from the manufacturer

Contact Wialon and achieve the most ambitious goals with telematics

Become a partner

Request Wialon in your region

Fill out a request form to get started with Wialon