Queclink GV800

Queclink GV800
Forum de discussion

Nombre des unités

1
En ligne
123
Nombre total
Caractéristiques Queclink GV800:
  • Boîte à mémoire
Compatible avec Wialon:
  • Connexion de caméra

Afin d'identifier le boîtier Queclink GV800 les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon :

Type du boîtier GPS: Queclink GV800
ID unique: imei

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Queclink GV800 pour les utiliser dans Wialon Hosting :

Port du serveur: 21644

123 unités Queclink GV800 connectées au le centre de données Wialon — Ça fait 0.01% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre Description Unités
csq_rssi The GSM signal strength level. The range is 0-31, 99 for unknown
csq_ber The quality of the GSM signal. The range is 0-7, 99 for unknown
is_pwr_ext Whether the external power supply is connected.
0 - not connected
1 - connected
pwr_ext The voltage of the external power supply V
pwr_int The voltage of the backup battery. The value of this field is only valid when the external power is not connected V
charging Whether the backup battery is charging when the main power supply is connected.
0 - not charging
1 - charging
led_on Indicate whether the LED’s are turned on
input_id ID of the input to which the fuel sensor is connected to, 0 means connected with serial port
battery The current volume of the backup battery %
1wire 1wire device data
harsh_speed_level The speed level of which the harsh behavior is detected:
0 - unknown speed
1 - low speed
2 - medium speed
3 - high speed
harsh_behavior Harsh behavior:
0 - harsh braking behavior
1 - harsh acceleration behavior
2 - harsh turn behavior
3 - harsh braking and turn behavior
4 - harsh acceleration and turn behavior
5 - Unknown harsh behavior
can_state CANBUS Device State:
0 - Abnormal. It fails to receive data from the external CANBUS device.
1 - Normal. It is OK to receive data from the external CANBUS device.

can_vin Vehicle identification number
can_ignition_key Ignition status:
0 - ignition off.
1 - ignition on.
2 - engine on.
can_total_dist_hect Vehicle total distance Hectometer (H)
can_total_dist_imp Vehicle total distance Impulse (I)
can_total_fuel_used Number of liters of fuel used since vehicle manufacture or device installation L
can_engine_rpm The revolutions per minute rpm
can_vehicle_speed The vehicle speed based on wheel km/h
can_eng_cool_temp Engine coolant temperature °C
can_fuel_consumpt The fuel consumption. The consumption is calculated depending on values read from vehicle.
Note: The CAN100 device cannot get this value and the value is invalid.
can_fuel_level_l The level of fuel in vehicle tank L
can_fuel_level_p The level of fuel in vehicle tank %
can_range The number of hectometer to drive on remaining fuel Hectometer (H)
can_acc_pedal_press Accelerator pedal pressure %
can_total_eng_hours Time of engine running since vehicle manufacture or device installation h
can_total_driv_time Time of engine running (non-zero speed) since vehicle manufacture or device installation h
can_eng_idle_time Time of engine running during idling status (vehicle stopped) since vehicle manufacture or device installation h
can_idle_fuel_used Total idle fuel used. Number of liters of fuel used since vehicle manufacture or device installation L
can_axle_weight Vehicle axle weight kg
can_driverN_time_st Driver N time related states:
0 - normal/no limits reached.
1 - 15 min before 41 h.
2 - 41 h reached.
3 - 15 min before 9 h.
4 - 9 h reached.
5 - 15 minute before 16 h (not having 8h rest during the last 24h).
6 - 16 h reached.
7 - other limit.
can_driverN_card Driver N card state:
1 - card inserted,
0 - no card inserted
can_driverN_work_st Driver N work state:
0 - normal / no limits reached.
1 - rest / sleeping.
2 - driver available / short break.
3 - drive / behind wheel.
can_indicators Detailed Information/Indicators:
Bit 1: FL – fuel low indicator (1 – indicator on, 0 – off).
Bit 2: DS – driver seatbelt indicator (1 – indicator on, 0 – off).
Bit 3: AC – air conditioning (1 – on, 0 - off).
Bit 4: CC – cruise control (1 – active, 0 - disabled).
Bit 5: B – brake pedal (1 – pressed; 0 – released).
Bit 6: C – clutch pedal (1 – pressed; 0 – released).
Bit 7: H – handbrake (1 – pulled-up, 0 – released).
Bit 8: CL – central lock (1 – locked, 0 – unlocked).
Bit 9: R – reverse gear (1 – on, 0 – off).
Bit 10: RL – running lights (1 – on, 0 – off).
Bit 11: LB – low beams (1 – on, 0 – off).
Bit 12: HB – high beams (1 – on, 0 – off).
Bit 13: RFL – rear fog lights (1 – on, 0 – off).
Bit 14: FFL – front fog lights (1 – on, 0 – off).
Bit 15: D – doors (1 – any door opened, 0 – all doors closed).
Bit 16: T – trunk (1 – opened, 0 – closed).
can_light Each bit contains information of particular light:
Bit 1: Running Lights (1 – on, 0 – off).
Bit 2: Low Beam (1 – on, 0 – off).
Bit 3: High Beam (1 – on, 0 – off).
Bit 4: Front Fog Light (1 – on, 0 – off).
Bit 5: Rear Fog Light (1 – on, 0 – off).
Bit 6: Hazard Lights (1 – on, 0 – off).
Bit 7: Reserved.
Bit 8: Reserved.
can_doors Each bit contains information of one door:
Bit 1: Driver Door (1 – opened, 0 – closed).
Bit 2: Passenger Door (1 – opened, 0 – closed).
Bit 3: Rear Left Door (1 – opened, 0 – closed)
Bit 4: Rear Right Door (1 – opened, 0 – closed).
Bit 5: Trunk (1 – opened, 0 – closed).
Bit 6: Boot (1 – opened, 0 – closed).
Bit 7: Reserved.
Bit 8: Reserved.
can_total_veh_ovspd The total time when vehicle engine speed is greater than the limit defined in CAN100's configuration
can_total_eng_ovspd The total time when vehicle engine speed is greater than the limit defined in CAN100's configuration
can_ad_blue_lvl The level of Ad-Blue
tacho_ovspd_sign The tachograph overspeed signal. The value 1 indicates "overspeed". The value 0 indicates "no overspeed"
tacho_motion_sign The tachograph vehicle motion signal. The value 1 indicates "motion". The value 0 indicates "no motion"
tacho_direction Vehicle driving direction obtained from tachograph
can_ain1 The value of analog input mV
can_engine_braking_factor Counts of braking with brake pedal or with engine
can_pedal_braking_factor Counts of braking with brake pedal or with engine
can_total_accel_kickdowns Total time when accelerator pedal is pressed over 90%
can_total_brakes The total number of braking processes initiated by brake pedal
tacho_drvN_card_number The card number of tachograph driver N
can_exp_info Detailed Information/Indicators:
Bit 1: W – webasto (1 – on, 0 – off or not available).
Bit 2: BFL – brake fluid low indicator (1 – on, 0 – off or not available).
Bit 3: CLL – coolant level low indicator (1 – on, 0 – off or not available).
Bit 4: BAT – battery indicator (1 – on, 0 – off or not available).
Bit 5: BF – brake system failure indicator (1 – on, 0 – off or not available).
Bit 6: OP – oil pressure indicator (1 – on, 0 – off or not available).
Bit 7: EH – engine hot indicator (1 – on, 0 – off or not available).
Bit 8: ABS – ABS failure indicator (1 – on, 0 – off or not available).
Bit 9: R – reverse.
Bit 10: CHK – check engine indicator (1 – on, 0 – off or not available).
Bit 11: AIR – airbags indicator (1 – on, 0 – off or not available).
Bit 12: SC – service call indicator (1 – on, 0 – off or not available).
Bit 13: OLL – oil level low indicator.
can_rapid_brakings Number of total rapid since installation
can_rapid_accels Number of total rapid accelerations since installation

Plus de boîtiers GPS de ce fabricant

Contactez Gurtam et atteignez les objectifs les plus ambitieux en télématique

Remplissez le formulaire pour commencer à travailler avec Wialon

Étape 1
Étape 2
Étape 3
Prénom et nom *
Entreprise*
Email*
Téléphone