Queclink GV56RS

Queclink GV56RS
Forum de discussion

Nombre des unités

17
En ligne
67
Nombre total
Compatible avec Wialon:
  • Communication via TCP
  • Communication via UDP

Afin d'identifier le boîtier Queclink GV56RS les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon:

Type du boîtier GPS: Queclink GV56RS
ID unique: imei

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Queclink GV56RS pour les utiliser dans Wialon Hosting:

Port du serveur: 21730

67 unités Queclink GV56RS connectées au le centre de données Wialon — Ça fait 0.01% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre Description Unités
dev_type Queclink device type
*HEX mode only
proto_ver Queclink protocol version
*HEX mode only
fw_ver Firmware version
*HEX mode only
battery Battery level, 0-100
pwr_ext External power source voltage
adc_mode Analog Input Mode
adc1 Analog Input 1 voltage
din_status Digital Input (bit mask)
dout_status Digital Output (bit mask)
motion_status
17 (0x11) Ignition off Rest: The vehicle is ignition off and motionless.
18 (0x12) Ignition off Motion: The vehicle had been moving before this action was regarded as car-towing event after ignition off.
33 (0x21) Ignition On Rest: The vehicle is ignition on and motionless.
34 (0x22) Ignition On Motion: The device is ignition on and moving.
65 (0x41) Sensor Rest: The vehicle is motionless and no ignition signal is detected.
66 (0x42) Sensor Motion: The vehicle is moving and no ignition signal is detected.
22 (0x16) Tow: The vehicle was towed after ignition off.
26 (0x1A) Fake Tow: The vehicle might have been towed after ignition off.
phone_number
ign_dur
ibutton
ibutton_auth
geo_id
ges_enabled
ges_mode
ges_radius
ges_dt
geo_area_type
geo_mask_group
geo_area_mask_group_1
geo_area_mask_group_2
jamming_cw
jamming_gps
upc_cmd_id
upc_result
url
x_forward
y_forward
z_forward
x_side
y_side
z_side
x_vert
y_vert
z_vert
onewire[i]_id
onewire[i]_type
onewire[i]_data
fuel_sensor[i]_type
fuel_sensor[i]_id
fuel_sensor[i]_percent
fuel_sensor[i]_volume
pwr_int
jamming_status
crash_counter
upd_code
upd_retry
idle_dt
gps_signal_status
wave1_out_id
wave1_out_active
temp_alarm_id
temp_status
temp_device_id
temp_device_data
roaming_state
curr_mileage Current Trip Mileage
*HEX mode only
total_mileage Total Mileage
*HEX mode only
curr_hourmetercount Current Trip Hour Meter Count (accumulative ignition time)
*HEX mode only
total_hourmetercount Total Hour Meter Count (accumulative ignition time)
*HEX mode only
hw_ver
mcu_ver
fri_discard_no_fix
resp_report_mask
ign_dt
igf_dt
bat_status
iccid
csq_ber CSQ BER,0-7/99
daylight_saving
time_zone
tcp_cmd_count
udp_cmd_count
sms_cmd_count_white
sms_cmd_count
tcp_msg_count
udp_msg_count
sms_msg_count_white
sms_msg_count
gir_trigger
mcc[i]
mnc[i]
lac[i]
cell_id[i]
ta[i]
rx_level[i]
gps_level
jamming_indicator
sat_[sv_id]
local_ip
ign_on_duration Duration since last time the ignition is on s
ign_off_duration Duration since last time the ignition is off s
report_type The message type of ASCII format report
device_status
16 (Tow) The device attached vehicle is ignition off and it is towed.
1A (Fake Tow) The device attached vehicle is ignition off and it might be towed.
11 (Ignition Off Rest) The device attached vehicle is ignition off and it is motionless.
12 (Ignition Off Motion) The device attached vehicle is ignition off and it is moving before it is considered to be towed.
21 (Ignition On Rest) The device attached vehicle is ignition on and it is motionless.
22 (Ignition On Motion) The device attached vehicle is ignition on and it is moving.
41 (Sensor Rest) The device attached vehicle is motionless without ignition signal detected.
42 (Sensor Motion) The device attached vehicle is moving without ignition signal detected.
eri_mask This mask is used to configure whether to report the data from peripherals via +RESP:GTERI

Plus de boîtiers GPS de ce fabricant

Actualités

Remplissez le formulaire pour commencer à travailler avec Wialon

Étape 1
Étape 2
Étape 3
Prénom et nom *
Entreprise*
Email*
Téléphone