Minitrack

Minitrack
Forum de discussion

Nombre des unités

9
En ligne
20
Nombre total
Caractéristiques Minitrack:
  • Boîte à mémoire

Afin d'identifier le boîtier Minitrack les détails suivants sont à utiliser dans les réglages de l'unité sur Wialon :

Type du boîtier GPS: Minitrack
ID unique: serial

Précisez les paramètres suivants dans le programme de configuration ou dans la configuration Minitrack pour les utiliser dans Wialon Hosting :

Port du serveur: 22006

20 unités Minitrack connectées au le centre de données Wialon — Ça fait 0% de nombre total des boîtiers GPS connectés.

Le diagramme ci-dessous représente la dynamique des connexions dans le centre de données Wialon au cours des 30 derniers jours:

Nom du paramètre Description Unités
adc Analog input sensor
mcc Mobile Country Code
mnc Mobile Network Code
lac Location Area Code
cell_id

cell ID

flag Current GSM Operator (2 nd and 3 rd Nibbles)
unit_status

0 bit - Communication with GPS is 1 - available / 0 - not available
1 bit - Network (0 - Home, 1 - Roam)
2 bit - Correct Time (1 - Invalid/estimated time stamp, 0 – Valid time stamp)
3 bit - Source of Speed (0 – GPS, 1 – Pulse frequency input)

reason Transmission Reason Specific Data
reason_data Transmission Reason
pwr_int

The voltage on the internal battery

pwr_ext

External power supply voltage

services

Bit 0 - Actual GNSS antenna selected (0 – Internal, 1 – External). (Relevant only for Cello GNSS variants)
Bit 1 - Trailer status indication. (0 – Trailer Disconnected, 1 – Trailer
Connected)

Bit 2 - 4 - CFE Type.

Bit 4 Bit 3 Bit 2 CFE Type
0 0 0 Not Applicable (Legacy state)
0 0 1 CFE is not connected
0 1 0 CFE BT is connected
0 1 1 CFE Basic is connected
1 0 0 CFE I/O is connected
1 0 1 CFE premium is connected
1 1 1 Undefined CFE Type

unit_mode

Unit Mode of Operation. The functioning of the unit can be generalized as a finite state machine model, with a few "stages" of operation. The "current stage" is referred to as "unit mode", or "mode of operation", as following:

Value Unit Mode Description
0x00 Standby Engine On
0x01 Standby Engine Off
0x02 Passive Arming (for security modifications)
0x03 Pre-Arming (for security modifications)
0x04 Alarm Armed (for security modifications)
0x05 Silent Delay (for security modifications)
0x07 Alarm Triggered (for security modifications)
0x0E Garage Mode
0x0F Transmissions Delay (for FW versions older than 25)
0x10 Towed mode (same as Standby Engine On, but with ignition off)

mode1, mode2

MODE 1 and Mode 2
These fields are generated by the GPS and transparently monitored in the outgoing message from the unit. The fields define the validity of GPS data in the message. The unit considers the valid fix according to the "Enable Tight GPS PMODE Filter" parameter (address 509, bit 7):
 If "Enable Tight GPS PMODE Filter" is enabled, the unit considers the GPS data as valid only if Mode 1 = 3 or 4 AND Mode 2 = 2
 If "Enable Tight GPS PMODE Filter" is disabled, the unit considers the GPS data as valid only if Mode 1 =2, 3, 4, 5 and 6

odom Mileage Counter (Odometer)

Plus de boîtiers GPS de ce fabricant

Contactez Wialon et atteignez les objectifs les plus ambitieux en télématique

Remplissez le formulaire pour commencer à travailler avec Wialon

Étape 1
Étape 2
Étape 3
Prénom et nom *
Entreprise*
Email*
Téléphone