StarLink Asset

StarLink Asset
Discusión en el foro

Cantidad de unidades

0
En línea
1
Total
Características StarLink Asset:
  • 3G
  • Caja negra
Soportado en Wialon:
  • Sensores ADC
  • Gestión remota vía GPRS
  • Sensores Digitales
  • LBS
  • Gestión remota vía SMS
  • Comunicación vía TCP

Para que el sistema de rastreo Wialon identifique los datos de StarLink Asset en el diálogo de configuración de la unidad, indique los siguientes datos :

Tipo de dispositivo: StarLink Asset
ID único: custom

Indique los siguientes parámetros en el programa de configuración o en la configuración StarLink Asset para utilizarlos en Wialon Hosting :

Puerto del servidor: 21790

En el centro de servicio Wialon se utilizan 1 unidades StarLink Asset — es 0% de la cantidad total de dispositivos Rastreador de activos conectados.

La gráfica representa la cantidad de conexiones en el centro de servicio Wialon en los últimos 30 días:

Nombre del parámetro Descripción Unidades de medida
alarm_armed Shows if alarm is armed. 0 - disarmed, 1 - armed
alarm_door Door state. 0 - closed, 1 - open
alarm_hood Hood state. 0 - closed, 1 - open
can_fuel_level CAN fuel level %
can_odometer CAN odometer value
can_rpm CAN engine revolutions per minute value r/min
can_speed km/h CAN speed value
event_id Code of the event
engine Engine. 0 - off, 1 - on
can Value 1 shows that message contains CAN data
in_port_e Input 3 / Port E value. 0 - off, 1 - on
immobilizer_armed Immobilizer state
in_port_f Input 4 / Port F value. 0 - off, 1 - on
odometer Odometer value m
out_port_b Output 2 / Port B value. 0 - off, 1 - on
pwr_ext Vehicle battery voltage V
pwr_int Backup battery voltage V
ref_num Message number
ign Ignition state. 0 - off, 1 - on
esafe_msg_type

Message type from eSafe:
137 - Maneuver notification, will be transmitted as Drive rule occurred if enabled
143 - Accident notification, will be transmitted as Accident detected if enabled
144 - Drive status changed
145 - Too many events
146 - Bad installation
147 - Possible accident notification

esafe_maneuv_type

The eSafe maneuver type:
1 - Acceleration
2 - Breaking
3 - Left turn
4 - Right turn
5 - Wide left turn
6 - Wide right turn
7 - Left turn while decelerating
8 - Left turn while accelerating
9 - Wide left turn while decelerating
10 - Wide left turn while accelerating
11 - Right turn while decelerating
12 - Right turn while accelerating
13 - Wide right turn while decelerating
14 - Wide right turn while accelerating
15 - Traffic circle
16 - Lane change
17 - Overtaking
18 - Speed bump
19 - Start of off-road driving
20 - End of off-road driving

esafe_maneuv_level

The eSafe maneuver level:
1 - Low
2 - Medium
3 - High

esafe_maneuv_dur The eSafe maneuver duration ms
esafe_force_x The eSafe maximum g force detected in the X axis g
esafe_force_y The eSafe maximum g force detected in the Y axis g
esafe_force_z The eSafe maximum g force detected in the Z axis g
esafe_accident_direct

The eSafe accident directions:
1 - Front
2 - Front left
3 - Front right
4 - Back
5 - Back left
6 - Back right
7 - Left
8 - Right
9 - Vehicle rolled over

esafe_driver_state

The eSafe driver state:
0 - Normal
1 - Aggressive
2 - Dangerous

esafe_aggres_maneuvers The eSafe total number of aggressive maneuvers
esafe_danger_maneuvers The eSafe total number of dangerous maneuvers
esafe_num_maneuvers The eSafe total number of maneuvers

You can also download an example of object configuration file for Starlink GLONASS to be used in Wialon GPS tracking software. When creating an object, import this configuration file by selecting "Import from File" option. This way you will create a pre-configured object with some sensors. Do not forget to specify the unique Id of Your device.

To get the dynamic parameters of the message send the command 03,01,177

Otros dispositivos del fabricante

Contacte con Wialon y logre los objetivos más ambiciosos con la telemática

Por favor, llene la solicitud para iniciar el trabajo con Wialon

Paso 1
Paso 2
Paso 3
Nombre y apellido*
Compañía*
Email*
Teléfono