Localizador GPS SSL-05 | Integrado con Wialon

Para que el sistema de rastreo Wialon identifique los datos de SSL-05 en el diálogo de configuración de la unidad, indique los siguientes datos :

Tipo de dispositivo:	SSL-05
ID único:	custom

Indique los siguientes parámetros en el programa de configuración o en la configuración SSL-05 para utilizarlos en Wialon Hosting :

Puerto del servidor:

22076

En el centro de servicio Wialon se utilizan 11 unidades SSL-05 — es 0% de la cantidad total de dispositivos Automóvil conectados.

La gráfica representa la cantidad de conexiones en el centro de servicio Wialon en los últimos 30 días:

Nombre del parámetro	Descripción	Unidades de medida
alarm_flag	Alarm (bitwise parameter, 1 - active, 0 - not active): bit1 - Emergency alarm, triggering after touching the alarm switch bit2 - Over Speed bit3 - Fatigue Driving bit5 - GNSS module malfunction bit6 - GNSS antenna disconnection bit7 - GNSS antenna short-circuit bit8 - Device low battery bit9 - Device power down bit14 - Over Speed bit15 - Fatigue Driving bit21 - Entry and exit an area bit22 - Entry and exit a route bit25 - Vehicle VSS malfunctions
state_flag	Status (bitwise parameter): bit1 - 0: ACC off; 1: ACC on bit2 - 0: No Position, 1: Positioned bit5 - 0: operational status; 1: outage status bit11 - 0: Vehicle oil-way is normal; 1: Vehicle oil-way is disconnected bit12 - 0: Vehicle circuit is normal; 1: Vehicle circuit is disconnected bit23 - 0: Electronic pulse signal is connected 1: Electronic pulse signal is disconnected bit24 - 0: Pulse Mode, when the speed signal disconnected, the device will be in the limp mode(Limited by GPS speed 25km/h), there will be a signal disconnection alarm report, 1: GPS Mode, Normal speed limiting, no signal disconnection alarm report. bit25 - 0: Close the blind zone, 1: Open the blind zone;
mileage	Mileage	km
mes_id	Message ID
result	General Terminal Response, result: 0 - Success/affirm, 1 - fail, 2 - false message, 3 - not support
fuel_volume	Oil level
speed_drvng_rec	Speed acquired by the driving record function
alarm_event_id	ID needed to manually confirm the alarm event
overspeed_alarm	Additional information on over-speed alarm exist
position_type	Additional overspeed alarm info 0: no specific location 3: polygon area
section_id	Additional overspeed alarm info Section ID, If the location type is 0, there is no field.
route_alarm	Additional information on the entry/exit of areas/routes alarm exist
direction	Direction, 0 - entry, 1 - exit
gsm	Wireless communication network signal strength
user_msg	User msg
norm_spd_lim	Normal speed limit threshold	km/h
area_id	The ID number of the current area where the vehicle enters in
curr_spd_lim	Current area speed limit threshold	km/h

Nombre del parámetro

Descripción

Unidades de medida

alarm_flag

Alarm (bitwise parameter, 1 - active, 0 - not active):
bit1 - Emergency alarm, triggering after touching the alarm switch
bit2 - Over Speed
bit3 - Fatigue Driving
bit5 - GNSS module malfunction
bit6 - GNSS antenna disconnection
bit7 - GNSS antenna short-circuit
bit8 - Device low battery
bit9 - Device power down
bit14 - Over Speed
bit15 - Fatigue Driving
bit21 - Entry and exit an area
bit22 - Entry and exit a route
bit25 - Vehicle VSS malfunctions

state_flag

Status (bitwise parameter):
bit1 - 0: ACC off; 1: ACC on
bit2 - 0: No Position, 1: Positioned
bit5 - 0: operational status; 1: outage status
bit11 - 0: Vehicle oil-way is normal; 1: Vehicle oil-way is disconnected
bit12 - 0: Vehicle circuit is normal; 1: Vehicle circuit is disconnected
bit23 - 0: Electronic pulse signal is connected 1: Electronic pulse signal is disconnected
bit24 - 0: Pulse Mode, when the speed signal disconnected, the device will be in the limp mode(Limited by GPS speed 25km/h), there will be a signal disconnection alarm report, 1: GPS Mode, Normal speed limiting, no signal disconnection alarm report.
bit25 - 0: Close the blind zone, 1: Open the blind zone;

mileage

Mileage

mes_id

Message ID

result

General Terminal Response, result:
0 - Success/affirm,
1 - fail,
2 - false message,
3 - not support

fuel_volume

Oil level

speed_drvng_rec

Speed acquired by the driving record function

alarm_event_id

ID needed to manually confirm the alarm event

overspeed_alarm

Additional information on over-speed alarm exist

position_type

Additional overspeed alarm info
0: no specific location
3: polygon area

section_id

Additional overspeed alarm info
Section ID, If the location type is 0, there is no field.

route_alarm

Additional information on the entry/exit of areas/routes alarm exist

direction

Direction,
0 - entry,
1 - exit

gsm

Wireless communication network signal strength

user_msg

User msg

norm_spd_lim

Normal speed limit threshold

km/h

area_id

The ID number of the current area where the vehicle enters in

curr_spd_lim

Current area speed limit threshold

km/h

Por favor, llene la solicitud para iniciar el trabajo con Wialon

Products

Soluciones de nicho para satisfacer las tareas específicas

SSL-05

Contacte con Wialon y logre los objetivos más ambiciosos con la telemática

Hacerse socio

Solicite Wialon en su región

Por favor, llene la solicitud para iniciar el trabajo con Wialon