| msg_type |
Type 2 |
|
| gps_validity |
Indicates the validity of the GPS, with value 1 valid position and value 0 Invalid position. |
|
| hdop |
HD information of the last valid GPS position. |
|
| sX_status |
Status of the tracker sensors (Part 1) value. Tracker sensors in two bits:
1 = disabled
2 = Activated (violated)
10 = Disabled (restored)
11 = Cut or error
Sensor Status 1 - MSB:
Bit 0 - Status of sensor 1
Bit 1 - Status of sensor 1
Bit 2 - Status of sensor 2
Bit 3 - Status of sensor 2
Bit 4 - Status of sensor 3
Bit 5 - Status of sensor 3
Bit 6 - Status of sensor 4
Bit 7 - Status of sensor 4
|
|
| ext_bat_status |
Status of external battery (1 = conected, 0 = disconected) |
|
| int_bat_status |
Status of the internal battery (1 = conected, 0 = disconected) |
|
| gps_ant_status |
Status of the external GPS antenna (1 = conected, 0 = disconected) |
|
| connect_bus_ign |
Ignition status (0 = ignition off 1 = ignition on) |
|
| k_sX_status |
Status of the keyboard sensors value in hexadecimal.
1 = disable
2 = enable (violated)
10 = disable (restored)
11 = Cut or error
Bit 0 - Status of keyboard sensor 1
Bit 1 - Status of keyboard sensor 1
Bit 2 - Status of keyboard sensor 2
Bit 3 - Status of keyboard sensor 2
Bit 4 - Status of keyboard sensor 3
Bit 5 - Status of keyboard sensor 3
Bit 6 - Status of keyboard sensor 4
Bit 7 - Status of keyboard sensor 4
|
|
| actuators_st1 |
Status of the actuators 1 tracker, value in hexadecimal.
Bit 0 - If value is equal to 1, indicates that the tracker is locked
Bit 1 - If value is equal to 1, indicates that the this tracker unlocked
Bit 2 - If value is equal to 1, indicates that the siren is connected
Bit 3 - If value is equal to 1, indicates that the buzzer is off
Bit 4 - If value is equal to 1, indicates that the lock is closed (if latch enabled)
Bit 5 - If value is equal to 1 indicates that the lock is open (when braking enabled)
Bit 6 - If value is equal to 1, indicates that the fifth wheel lock is open (when enabled fifth wheel)
Bit 7 - If value is equal to 1, indicates that the fifth wheel lock is closed (enabled when the fifth wheel)
|
|
| actuators_st2 |
Status of the tracker actuators 2 value in hexadecimal.
Bit 0 - If value is equal to 1, indicates that the flash alert is on
Bit 1 - If value is equal to 1, indicates that the flash alert is off
Bit 2 - For future use (always 0)
Bit 3 - For future use (always 0)
Bit 4 - For future use (always 0)
Bit 5 - For future use (always 0)
Bit 6 - For future use (always 0)
Bit 7 - For future use (always 0)
|
|
| ext_bat_volt |
Voltage external battery, vehicle in volts. |
V |
| int_bat_volt |
Voltage internal battery, tracker, in volts. |
V |
| connect_bus_odom |
Odometer |
km |
| gsm_signal |
GSM modem signal level. This value is between 0 (weak) to 31 (strongest signal). |
|
| temp |
For the temperature sensor, if a value of 0xFF indicates disabled sensor. Value in hexadecimal. If the value other than 0xFF, then the temperature sensor is enabled, in this case following: Bit 0 - temperature value - LSB Bit 1 - Value temperature Bit 2 - Value temperature Bit 3 - Value temperature Bit 4 - Value temperature Bit 5 - Value temperature Bit 6 - temperature value - MSB Bit 7 - Signal - if value of 1 indicates negative value if value of 0 indicates a positive value If the value is equal to 0xFE indicates that the temperature sensor is faulty hardware or not installed any temperature sensor.
|
|
| seals |
Status of the seals of the keyboard tracker sensors value in hexadecimal. MSB: If value 1 = 0 = sealed or unsealed Bit 0 - Sensor 3 keyboard Bit 1 - Sensor keyboard 4 Bit 2 - For future use, always 0 Bit 3 - For future use, always 0 Bit 4 - For future use, always 0 Bit 5 - For future use, always 0 Bit 6 - For future use, always 0 Bit 7 - For future use, always 0 LSB: If value 1 = 0 = sealed or unsealed Bit 0 - 1 Sensor tracker Bit 1 - Sensor 2 crawler Bit 2 - Sensor 3 crawler Bit 3 - Sensor 4 tracker Bit 4 - 5 Sensor tracker Bit 5 - Sensor 6 crawler Bit 6 - keyboard Sensor 1 Bit 7 - Keyboard Sensor 2
|
|
| crawler_status |
Crawler logical status: Value 1 = switched on in ignition mode Value = 2 in ignition off mode Value = 3 in sleep mode Value = 4 in internal battery mode value = 5 in deep sleep mode (post-production) Value = 6 in breach mode Value = 7 in super sleep mode (mobile)
|
|
| movement_accel |
Movement accelerometer (since the accelerometer is enabled) (1 = moving or 0 = stopped)
|
|
| accel_enabled |
Accelerometer enabled (1 = enabled or 0 = disabled)
|
|
| anti_theft_mode |
Much of the Fault Codes |
|
| travel_mode |
Traveling mode (only when keyboard attached) (1 = 0 = way trip or stop mode)
|
|
| mixer_status |
Mixer status (provided it is properly configured) 000 = Not enabled 001 = Stop mixer 010 = Mixer turning left (unloading) 011 = Mixer turning right (beating the cement) 100 = Mixer cement loading 111 = Invalid State
|
|
| rain_sensor |
Rain sensor (provided it is properly configured) (1 = enabled or disabled = 0)
|
|
| rem_fw_update |
Remote Firmware Update (1 = enabled or disabled = 0)
|
|
| jammer |
Active Jammer and detected (1 = enabled or disabled = 0)
|
|
| charger_status |
Ccharger status of the internal battery 00 = no charger information 01 = loading process 10 = suspended load 11 = finished loading
|
|
| event_id |
Event id (for msg_type = 47)
|
|
| event_paramX |
Event parameters (number and meaning are based on event_id)
|
|
| connect_bus_power_windows |
Power windows |
|
| connect_bus_spraying_sections_state |
State of the spraying sections
|
state |
| connect_bus_motor_load |
Motor load
|
% |
| connect_bus_battery_charge_state_ev |
Charging type an EV
|
|
| connect_bus_cooling_liquid_temp |
Cooling liquid temperature
|
|
| connect_bus_engine_oil_pressure |
Engine oil pressure
|
kPa |
| connect_bus_tire_pressure_td |
The pressure of the Tire on the head |
|
| connect_bus_i2_type |
Type of the second input
["Generic", "Hanger spindle", "Locking differential", "Dancer", "Wiper blade on the windscreen", "Resistance", "Violation of a Panel ON", "Default Panel-NF", "Panic-Button"]
|
|
| connect_bus_fuel_type |
The type of the fuel
["Methane", "Ethanol", "Diesel"]
|
|
| connect_bus_app_volume_rate |
The rate of the Volume of the App, for HA
|
|
| connect_bus_alarm |
Alarm |
|
| connect_bus_water_in_fuel |
The indicator of the Water-In-Fuel sensor: Off, On
|
state |
| connect_bus_cotton_platform |
Platform cotton state: Down Lower, Rising
|
|
| connect_bus_i2_value |
Value of the second input
|
V |
| connect_bus_motor_torque |
Motor torque
|
Nm |
| connect_bus_battery_health_ev |
Battery health (EV)
|
|
| connect_bus_o2_signal |
Signal of the second output ["Disabled", "Digital", "Digital" inverted", "RANGE"]
|
signal |
| connect_bus_cane_elevator_treadmill |
State of the cane elevator treadmill ["Off", "On"]
|
|
| connect_bus_motor_torque_percentage |
Torque motor percentage
|
% |
| connect_bus_water_pump_sprayer |
Water pump sprayer state
["Off", "On"]
|
|
| connect_bus_o2_type |
The type of the second output
["Generic", "Lock", "Lock box", "Relay-L15", "Siren"]
|
|
| connect_bus_fuel_flow |
Total fuel flow
|
(l/h) |
| connect_bus_passenger_door |
Passenger door state (EV)
|
|
| connect_bus_pump_to_diesel_flow |
The flow from the Pump to a Diesel
|
|
| connect_bus_clutch_pedal |
Clutch pedal state
|
|
| connect_bus_acc_pedal |
Accelerator pedal pressure
|
% |
| connect_bus_door_passenger |
State of the passenger door
|
|
| connect_bus_air_conditioning_pwr_ev |
The power of the Air-Conditioning system (IV) |
|
| connect_bus_liquid_release_spray |
["Off", "On"] |
|
| connect_bus_cane_production |
["Off", "On"]
|
|
| connect_bus_battery_average_savings_ev |
Average savings of Battery power (EV) |
|
| connect_bus_pto |
PTO active
|
|
| connect_bus_gear |
Gear |
march |
| connect_bus_electric_motor_temp_ev |
The temperature of the Electric Motor (EV) |
°C |
| connect_bus_fault_codes_amount |
Fault codes amount
|
|
| connect_bus_heater_pwr_ev |
The power of the Heater (EV)
|
|
| connect_bus_msg_type |
Message type
00 OK
01 out of range
02 challenge timeout
03 Invalid challenge response
04 Lock activation not enabled on HW
05 CAN communication timeout
06 CAN initialization error
07 CAN encryption error
08 Error in CAN lock/unlock actuation
09 Did not correctly record/execute the procedure
10 Microcontroller flash memory problem
11 Vehicle communication error
12 Seed collection error
13 Key sending error
14 Error reading lock write confirmation
15 Error writing lock
16 Incompatible ECU Software Information/Number
17 Error maintaining communication with the vehicle
18 CAN0 communication not found
19 CAN1A communication not found
20 CAN1B communication not found
21 J1587 communication not found
22 KWP1 communication not found
23 KWP2 communication not found
24 CAN0 and CAN1A communication not found
25 CAN0, CAN1A and CAN1B communication not found
26 CAN1A and CAN1B communication not found
27 CAN0 and J1587 communication not found
28 CAN1A and J1587 communication not found
29 CAN0, CAN1A and J1587 communication not found
30 vehicle turned off
31 moving vehicle
34 KWP error during lock/unlock procedure
35 Backup not available at start of lock/unlock
36 Error reading parameters for blocking
37 Cylinder cutting error
38 Error during KWP seed request
39 Error did not accept KWP key command
40 Vehicle error did not respond to KWP key command
41 Error reading backup information
42 Size error comparing backups
43 Error comparing backups
44 Authentication session error
45 Reentrant function error
46 invalid tracker error
47 timeout error
48 Accelerator pedal pressed error
|
|
| connect_bus_fuel_level |
Fuel Level
|
% |
| connect_bus_oil_engine_pressure |
The pressure of the engine oil
|
|
| connect_bus_e_pedal |
E-pedal State (EV)
|
|
| connect_bus_tire_pressure_te |
Tire pressure (TE)
|
Psi |
| connect_bus_cotton_harvesting_unit |
Cotton harvesting state
|
|
| connect_bus_charging_cable_ev |
A Charging cable is Plugged in (EV) |
|
| connect_bus_brake_time |
Time to brake
|
s |
| connect_bus_headlights |
The state of the lights |
|
| connect_bus_speed_ev |
Vehicle speed (EV)
|
|
| connect_bus_coupler_back |
position of the coupler back
|
% |
| connect_bus_tire_pressure_de |
Tire pressure DE
|
|
| connect_bus_o2_value |
Value of the second output
|
|
| connect_bus_cotton_packer |
Cotton packer state
["Off", "On"]
|
|
| connect_bus_brake_parking |
Brake, Parking
|
|
| connect_bus_electric_motor_current_ev |
Electric motor current (EV)
|
|
| connect_bus_airbag |
Airbag state
|
|
| connect_bus_arla32_level |
ARLA32 level
|
|
| connect_bus_dtc_present |
["No fault", "fault"]
|
|
| connect_bus_lever |
State of the lever
["Down", "Right", "Left"]
|
|
| connect_bus_rtk_autopilot |
State-BASE / Auto-Pilot
["Off", "On"]
|
|
| connect_bus_eng_on_dur |
Duration of engine on
|
|
| connect_bus_engine_rpm |
Revolutions per minute of the engine
|
rpm |
| connect_bus_int_resist |
Resistance of internal battery
|
V |
| connect_bus_hitch_to_front |
Position of hitch to the front
|
% |
| connect_bus_load_speed |
Load speed of the motor
|
|
| connect_bus_seatbelt_passenger |
Seatbelt, Driver
["Not fastened", "Buckled"]
|
|
| connect_bus_i1_value |
Value of the first input
|
|
| connect_bus_ign_on_duration |
Duration of Ignition On
|
|
| connect_bus_air_temp |
Air temperature
|
|
| connect_bus_intake_air_pressure |
Intake air pressure
|
|
| connect_bus_blink_warning |
Blink warning ["Off", "On"]
|
|
| connect_bus_clutch |
Clutch switch
["Moving", "Stationary", "Open", "Closed"]
|
|
| connect_bus_engine_brake_mode |
Engine brake mode:
- The regulator in slow motion
- Accelerator Pedal
- Cruise control
- Regulatory SYSTEM
- the Regulator speed
- Traction Control
- Transmission
- ABS
- Torque-Limiting
- Lever, high-speed
- The brake system
- Gas pedal
- remote
|
|
| connect_bus_out_turbo_oil_temp |
Oil temperature in turbo
|
°C |
| connect_bus_right_rear_door |
["Open", "Closed", "Locked"] |
|
| connect_bus_charging_type_ev |
["Not Loading", "Slow Loading", "Fast Loading"]
|
|
| connect_bus_o1_type |
["Generic", "Lock", "Lock box", "Relay-L15", "Siren"]
|
|
| connect_bus_battery_life_ev |
Battery life (EV)
|
|
| connect_bus_lambda |
|
|
| connect_bus_time_to_charge_80 |
The time of 80% charge (EV)
|
h |
| connect_bus_seatbelt_driver |
State of the driver's seatbelt
["not fastened", "Buckled"]
|
|
| connect_bus_charging_voltage_ev |
Charging voltage type (EV)
["Not loading", "AC", "DC"]
|
State |
| connect_bus_eco_mode |
Eco-mode state (EV)
["Off", "On"]
|
|
| connect_bus_intake_manifold_temp |
Engine Intake Manifold 1 Temperature
|
|
| connect_bus_door_driver |
State of the driver's door
["Open", "Closed", "Locked"]
|
|
| connect_bus_primary_air_pressure |
Pressure In The Air Reservoir, The Primary
|
|
| connect_bus_trans_oil_temp |
Transmission oil temperature
|
°C |
| connect_bus_fuel_temp |
Fuel temperature
|
°C |
| connect_bus_primary_air_reservoir_pressure |
The pressure of the Air in the Reservoir, the Primary |
|
| connect_bus_pwr_int |
Internal voltage
|
V |
| connect_bus_engine_hours |
Total engine hours
|
|
| connect_bus_air_conditioning_temp |
The Selected temperature of the Air-Conditioning system |
°C |
| connect_bus_current_battery_capacity_ev |
The Current capacity of the Battery (EV) |
|
| connect_bus_speed |
The speed determined by the tachograph
|
|
| connect_bus_pwr_int_ev |
Interval power voltage
|
|
| connect_bus_oil_hydraulic_temp |
Oil hydraulic temperature
|
|
| connect_bus_grain_unloading |
["Off", "On"]
|
|
| connect_bus_wiper_blade |
Wiper Blade for windshield
["Off", "On"]
|
|
| connect_bus_trunk |
["Open", "Closed", "Locked"]
|
|
| connect_bus_full_charge_time_ev |
Charge time to full (100%) (EV)
|
|
| connect_bus_payload_ver |
Version of the payload like 1.2.3
|
|
| connect_bus_traction |
Traction
|
|
| connect_bus_left_rear_door |
["Open", "Closed", "Locked"]
|
|
| connect_bus_eng_oil_level |
Oil level in engine
|
% |
| connect_bus_distance_to_service |
Distance to the Service |
|
| connect_bus_battery_output_pwr_ev |
Battery voltage (EV)
|
|
| connect_bus_i1_signal |
Signal of the first input
["Disabled", "Digital", "Analog"]
|
|
| connect_bus_i2_signal |
Signal of the second input
["Disabled", "Digital", "Analog"]
|
|
| connect_bus_tire_pressure_dd |
Tire pressure (DD)
|
Psi |
| connect_bus_o1_value |
Value of output 1
|
V |
| connect_bus_clutch_time |
Time to clutch
|
|
| connect_bus_engine_brake |
Engine brake state
["Off", "On"]
|
|
| connect_bus_load_code |
Load code
|
|
| connect_bus_turbo_pressure |
Turbo pressure
|
Nm |
| connect_bus_angle |
The angle of the steering Wheel
|
° |
| connect_bus_tank_ethanol_percentage |
Percentage of Ethanol in the Tank |
|
| connect_bus_maximum_battery_capacity_ev |
The Maximum capacity of the Battery (EV) |
|
| connect_bus_i1_type |
Type of the input 1
["Generic", "Hanger spindle", "Locking differential", "Dancer", "Wiper blade on the windscreen", "Resistance", "Violation of a Panel ON", "Default Panel-NF", "Panic-Button"]
|
|
| connect_bus_instant_savings |
Instant savings
|
|
| connect_bus_odometer |
Hour meter |
km |
| connect_bus_nitrogen_oxides_nox |
Nitrogen oxides (Nox)
|
ppm |
| connect_bus_average_savings |
Average savings
|
|
| connect_bus_court_pressure |
Court pressure
|
|
| connect_bus_primary_cane_extractor |
State of the cane extractor
|
|
| connect_bus_total_fuel |
Total fuel used
|
l |
| connect_bus_battery_temp_ev |
Temperature of the battery (EV)
|
|
| connect_bus_air_conditioning |
["Off", "On"]
|
|
| connect_bus_o2_percentage |
O2 Percentage
|
|
| connect_bus_eng_oil_temp |
Engine oil temperature
|
|
| connect_bus_available_regeneration_pwr_ev |
Available regeneration power (EV)
|
|
| connect_bus_the_modes_of_the_engine_brake |
Modes of the engine brake
["The regulator in slow motion", "accelerator Pedal", "Cruise control", "Regulatory SYSTEM", "the Regulator speed", "traction Control", "Transmission", "ABS", "torque-Limiting", "lever, high-speed," "the brake system", "gas pedal", "remote"]
|
|
| connect_bus_brake_pedal |
Brake pedal state
|
|
| connect_bus_o1_signal |
Signal of the output 1
["Disabled", "Digital", "inverted", "RANGE"]
|
|
| connect_bus_proto_ver |
Connect bus protocol version: v1 or v4
|
|
| rf433_state |
RF module status:
if received value = 167, then connected
any other value = disabled
|
|
| delivery_time |
The time of activation of the current module
|
s |
| last_activation_id |
The ID of the last of the activation, and if the value is equal to:
0 = disabled,
1 = wake-up command to the serial
2 = wake-up command via the server
3 = wake-up detection of the cell
4 = the activation, as a rule, without communication, GPRS,
5 = all of the wake-up command via sms
to 6 = activation by the rule of the inclinometer,
7 = activation, usually by the removal of the simcard
|
|
| last_tombstone_id |
The ID of the last shutdown, if the value is equal to:
0 = disabled,
1 = disable for the command-serial,
2 = off command via the server,
3 = disable detection of the cell
4 = off, as a rule, without communication, GPRS,
5 = disable command, via sms,
6 = off, as a rule for the inclinometer,
7 = off, as a rule for the removal of the simcard
|
|
| melody |
The kind of song that, if the value is equal to:
0 = NO BEEP-BEEP-OLD
AND 1 = BEEP ONCE,
2 = A LONG BEEP AND A SHORT BEEP
AND 3 = A SHORT BEEP AND A LONG BEEP
AND 4 = ONE LONG BEEP AND TWO SHORT BEEPS -
5 = TWO SHORT BEEPS AND ONE LONG BEEP
6 = ONCE AGAIN, AND ONCE OLD
7 = SHORT BEEP LOOK
8 = LONG BEEP LOOK
9 = BEEPER FOR A SUPER LONG LOOK
|
|
| comm_frequency |
The value of the frequency of communication: RF
|
|
| ext_analog_reader |
Information of the reader, external analog
Information is not sent in the ASCII protocol
|
|
| max_speed_gps |
The value of the maximum speed of the GPS between the message tracking (position)
|
|
| fuel_system_status |
If the value is 0, The motor is switched off
If the bit is 0, 1 = open Circuit, due to the temperature, not the engine
If the bit is 1, where 1 = closed-loop, using the feedback from the oxygen sensor in order to determine the mixture of the fuel
Bit 2 1 = open Circuit due to the load on the engine fuel, due to the slowdown in
Bit 4 1 = open Circuit due to a fault in the system
Bit 5 1 = closed Circuit, by using at least one oxygen sensor, but there is a glitch in the system, feedback,
|
|
| motor_load |
Percentage or of the load current of the motor (from 0 up to 100%)
|
% |
| cooling_liquid_temp |
The current value of the temperature of the liquid coolant in the engine
|
|
| fuel_pressure |
The current value of the pressure in the fuel you need to multiply by 3 to get the value
|
kPa |
| rpm |
The current value of the RPM of the engine
|
|
| speed |
The current value for the speed of the vehicle
|
|
| distance_indicator |
Current value-led in the distance traveled (the information that is available only on the protocol (OBD2) |
|
| fuel_level |
The current value of the level of the fuel tank |
|
| engine_oil_temp |
The current value of the temperature of the oil in the motor
|
|
| clearing_codes_dist |
The current value of the distance from the cleaning up of the code information is available to you only on the protocol (OBD2)
|
|
| odometer |
The current odometer |
|
| room_temp |
The current value of the ambient temperature |
|
| total_fuel_used |
The current value of your total fuel used, source of information that is available only for internet protocol J1939)
|
|
| fuel_economy |
The current value of the economy, instant fuel source of information that is available only for internet protocol J1939)
|
|
| acc_pedal |
The current value of the position of the accelerator pedal (the information is only available for internet protocol J1939)
|
|
| brake_pedal |
The current value of the position of the brake pedal (the information is only available for internet protocol J1939)
|
|
| torque |
The current value of the torque of information that is available only for internet protocol J1939)
|
|
| reverse_current |
The current value of the reverse current information that is available only for internet protocol J1939)
|
|
| total_engine_hours |
Accumulated time of operation of the engine (the information is only available for internet protocol J1939)
|
|
| add_info2 |
The formatted value in the hex containing the bits to the additional information in part 2
|
|
| sysconfig |
The current value of the range, the message will be sent the tracking information on the sleep that is used by the crawler
|
|
| prev_sysconfig |
The value of the previous range, the message will be sent multiple tracking in sleep
|
|
| sysconfig_change_ts |
The Timestamp of the last change in the value of the setting range, the message will be sent the tracking is in the sleep
|
|
| max_rpm |
The value of the RPM to the maximum measured during the interval of the delivery of the message tracking
|
|
| min_rpm |
The value of the RPM to the minimum measured during the interval mum of the delivery of the message tracking
|
|
| avg_rpm |
The value of RPM is the average measured at the interval of the delivery of the message tracking
|
|
| comm_tech |
The value of the communication technologies
0 = undefined GSM,
1 = GSM (2G)
2 = WCDMA,
3 = LTE
4 = GSM
5 = ALL OF THE DYNAMIC RANGE (HDR)
6 = TDSCDMA
7 = EMTC
8 = NB.
|
|
| hour_meter_ign_on |
The total amount of the tracer when the ignition is switched on |
s |
| rf_sn |
The serial number read from the tracker or the height of a lock to the RF that is configured as a master or a slave that is connected to this tracker
|
|
| rf_fw_version |
The current version of the firmware of the module
|
|
| actuator_status_tracker |
The Status of the actuator, a value that is in hexadecimal
Bit 0 – no Actuator (1) of the crawler -
Bit, 1 – Actuator, 2 crawler -
Bit, 2 – Actuator (3) of the crawler -
Bit, 3 – Actuator-4 crawler -
Bit, 4 – Actuator-5 crawler - tracker
Bit, 5 – Actuator-6 crawler -
Bit 6 – Not used (always zero)
Bit 7 – Not used (always zero)
If the bit is equal to 1 = actuator is turned on
If the bit is equal to 0 = actuator is turned off
|
|
| actuator_status_keypad |
The Status of the actuator, a value that is in hexadecimal
Bit 0 – no Actuator (1) of the keyboard -
Bit, 1 – Actuator, 2 keyboard -
Bit, 2 – Actuator (3) keyboard -
Bit, 3 – Actuator (4) of the keyboard,
Bit 4 – Not used (always zero)
Bit 5 – Not used (always zero) keypad
Bit 6 – Not used (always zero)
Bit 7 – Not used (always zero)
If the bit is equal to 1 = actuator is turned on
If the bit is equal to 0 = actuator is turned off
|
|
| cumul_hour_meter_tristate_X |
The time is measured to the hour meter from 0 to 4294967295
|
s |
| cumul_hour_meter_wrist_X |
The time is measured to the hour meter from 0 to 4294967295
|
s |
| cumul_hour_meter_digital_X |
The time is measured from the hour meter 0 to 4294967295
|
s |
