Cellocator CR300

Fabricante: Pointer Telocation

Discusión en el foro

Cantidad de unidades

1006

En línea

1981

Total

Información
Parámetros

Características Cellocator CR300:

3G
Caja negra

Soportado en Wialon:

Acelerómetro
Sensores ADC
Datos de CAN
Manejo remote via GPRS
Indentificación del conductor
Sensores Digitales
LBS
Envío de datos por SMS
Comunicación vía TCP

Para que el sistema de rastreo Wialon identifique los datos de Cellocator CR300 en el diálogo de configuración de la unidad, indique los siguientes datos:

Tipo de dispositivo:	Cellocator CR300
ID único:	serial

Indique los siguientes parámetros en el programa de configuración o en la configuración Cellocator CR300 para utilizarlos en Wialon Hosting:

Puerto del servidor:

21269

En el centro de servicio Wialon se utilizan 1981 unidades Cellocator CR300 — es 0.17% de la cantidad total de dispositivos Automóvil conectados.

La gráfica representa la cantidad de conexiones en el centro de servicio Wialon en los últimos 30 días:

Nombre del parámetro

Descripción

Unidades de medida

adc

Analog input sensor

mcc

Mobile Country Code

mnc

Mobile Network Code

lac

Location Area Code

cell_id

cell ID

flag

Current GSM Operator (2 nd and 3 rd Nibbles)

unit_status

0 bit - Communication with GPS is 1 - available / 0 - not available
1 bit - Network (0 - Home, 1 - Roam)
2 bit - Correct Time (1 - Invalid/estimated time stamp, 0 – Valid time stamp)
3 bit - Source of Speed (0 – GPS, 1 – Pulse frequency input)

reason

Transmission Reason Specific Data

reason_data

Transmission Reason

pwr_int

The voltage on the internal battery

pwr_ext

External power supply voltage

services

Bit 0 - Actual GNSS antenna selected (0 – Internal, 1 – External). (Relevant only for Cello GNSS variants)
Bit 1 - Trailer status indication. (0 – Trailer Disconnected, 1 – Trailer
Connected)

Bit 2 - 4 - CFE Type.

Bit 4	Bit 3	Bit 2	CFE Type
0	0	0	Not Applicable (Legacy state)
0	0	1	CFE is not connected
0	1	0	CFE BT is connected
0	1	1	CFE Basic is connected
1	0	0	CFE I/O is connected
1	0	1	CFE premium is connected
1	1	1	Undefined CFE Type

unit_mode

Unit Mode of Operation. The functioning of the unit can be generalized as a finite state machine model, with a few "stages" of operation. The "current stage" is referred to as "unit mode", or "mode of operation", as following:

Value Unit Mode Description
0x00 Standby Engine On
0x01 Standby Engine Off
0x02 Passive Arming (for security modifications)
0x03 Pre-Arming (for security modifications)
0x04 Alarm Armed (for security modifications)
0x05 Silent Delay (for security modifications)
0x07 Alarm Triggered (for security modifications)
0x0E Garage Mode
0x0F Transmissions Delay (for FW versions older than 25)
0x10 Towed mode (same as Standby Engine On, but with ignition off)

mode1, mode2

MODE 1 and Mode 2
These fields are generated by the GPS and transparently monitored in the outgoing message from the unit. The fields define the validity of GPS data in the message. The unit considers the valid fix according to the "Enable Tight GPS PMODE Filter" parameter (address 509, bit 7):
 If "Enable Tight GPS PMODE Filter" is enabled, the unit considers the GPS data as valid only if Mode 1 = 3 or 4 AND Mode 2 = 2
 If "Enable Tight GPS PMODE Filter" is disabled, the unit considers the GPS data as valid only if Mode 1 =2, 3, 4, 5 and 6

odom

Mileage Counter (Odometer)

Otros dispositivos del fabricante

‹ › ×

Gurtam products

Soluciones de nicho para satisfacer las tareas específicas

Cellocator CR300

Otros dispositivos del fabricante