ATrack AX9

ATrack AX9
Fabricante: ATrack
Discusión en el foro

Cantidad de unidades

4
En línea
51
Total
Características ATrack AX9:
  • Caja negra
  • Odómetro incorporado
Soportado en Wialon:
  • Acelerómetro
  • Gestión remota vía GPRS
  • LBS
  • Gestión remota vía SMS
  • Comunicación vía TCP
  • Comunicación por UDP

Para que el sistema de rastreo Wialon identifique los datos de ATrack AX9 en el diálogo de configuración de la unidad, indique los siguientes datos :

Tipo de dispositivo: ATrack AX9
ID único: custom

Indique los siguientes parámetros en el programa de configuración o en la configuración ATrack AX9 para utilizarlos en Wialon Hosting :

Puerto del servidor: 21184

En el centro de servicio Wialon se utilizan 51 unidades ATrack AX9 — es 0.06% de la cantidad total de dispositivos OBD conectados.

La gráfica representa la cantidad de conexiones en el centro de servicio Wialon en los últimos 30 días:

Nombre del parámetro Descripción Unidades de medida
pwr_ext Voltage of external power supply V
pwr_int Power supply internal battery V
gsm GSM signal quality
pulse_count Pulse count value
engine_rpm Engine RPM reading
gsm_status GSM status
dt 0-Real time report
mf Mass Air Flow Rate in 0.01grams/sec
el Engine Load %
tr Throttle position %
ml MIL (Malfunction Indicator Lamp) status
coolant_temp Engine Coolant Temperature °C
fuel_level Fuel Level %
fuel_consumption Fuel Used in 0.1 liter
analog_volt Analog voltage reading
max_speed Maximum speed between two reports
gl Google Link (N/A in AX5)
gx X-axis acceleration

0.0098*m/s2

gy Y-axis acceleration

0.0098*m/s2

gz Z-axis acceleration

0.0098*m/s2

motion Vehicle motion event status
engine Engine event status
Model Name: Device Model Name
Firmware Ver: Device firmware version information
IMEI: International Mobile Equipment Identity number (Not available in AY5(i); 0 is shown)
IMSI: International Mobile Subscriber Identity (Not available in AY5(i); 0 is shown)
CID: Card identification number of SIM card (Not available in AY5(i); 0 is shown)
Main Volt: Main power voltage in 0.1 V
Battery Volt: Backup battery voltage in 0.1 V
SATS: Numbers of GPS satellite currently used
GSM Status:

GSM Network registration status (Not available in AY5(i); 0 is shown):
0: Network not registered
1: Registered to home network
2: Searching for available network
3: Registration denied
4: Unknown
5: Registered, roaming

GPS Status:

GPS antenna status:
Bit 0: 0 -> GPS antenna connected
&nbsp &nbsp &nbsp &nbsp &nbsp 1 -> GPS antenna disconnected
Bit 1: 0 -> GPS antenna cable OK
&nbsp &nbsp &nbsp &nbsp &nbsp 1 -> GPS antenna cable short circuit
Bit 2: 0 -> GPS signal reception OK
&nbsp &nbsp &nbsp &nbsp &nbsp 1 -> GPS signal reception timeout

tracking_mode

The GPS tracking Mode parameter can be in conjunction with the following bits:
Bit 0: Time mode
Bit 1: Distance mode
Bit 2: ACC status (Must combine with Bit 0 or Bit 1)
Bit 3: Heading change condition
Bit 4: Minimum speed (Must combine with Bit 0 or Bit 1)
Bit 5: Engine status = ON. (Must combine with Bit 0 or Bit 1)
Bit 6: Motion status = ON. (Must combine with Bit 0 or Bit 1)
Bit 7: Logical Operation Mode (0=AND; 1=OR; Default=0) This mode only works when combining Time, Distance, and/or Heading change. Bit 8: Reset tracking timer when event report is sent
Bit 9: Report with unique ID when in Distance Mode (Must combine with Bit 1)

min_send_time Minimum time in seconds that must elapse before reporting next position. (Min. 1 seconds)
min_send_dist Minimum distance in multiple of 10 meters that must be traveled before reporting next position. (Min. 20 meters)
min_heading Minimum heading in degree that must be changed before reporting next position. (15..180)
min_speed Minimum speed in km/h that must be achieved before reporting next position.
track_times

Specify tracking times. =0 means forever tracking.

dest_type

Specify the destination for tracking report position The parameter is in conjunction with the following bits:
0: Default communication type. (i.e. Command issuer)
Bit 0: SMS
Bit 1: GPRS (This is the only option for AY5)
Bit 2: USSD
Bit 3: Serial

sched

Specify the schedule for the report. The parameter is in conjunction with the following bits:
0 – indicates use no schedule (i.e. always on)
Bit 0 – Schedule 1
Bit 1 – Schedule 2
Bit 2 – Schedule 3
Bit 3 – Schedule 4
Bit 4 – Schedule 5
Bit 5 – Schedule 6
Bit 6 – Schedule 7
Bit 7 – Schedule 8

acc_off_time Minimum time in seconds that must elapse before reporting next position while the ACC is in Off status. ACC status in Mode must be set in order to use this time interval. (Min. 1 seconds)
coll_num Number of position to be put into one TCP/UDP packet
temp_a_id The sensor ID corresponding to temperature A
curr_a_temp The temperature reading from sensor ID A
temp_b_id The sensor ID corresponding to temperature B
curr_b_temp The temperature reading from sensor ID B
sensor_index

The connected port number where the Temperature Sensor connected with by different user.
1: First detected sensor
2: Second detected sensor

min_temp Minimum temperature value, and is in 0.1 °C
max_temp Maximum temperature value, and is in 0.1 °C
hold_duration A temperature holding time, and is in minute unit.
sensor_id Temperature sensor ID. This temperature sensor can be set to be index 1 or 2 by specifying the ID in this field.
status

Current status of RPM over-revving event
0: RPM (Engine over-revving) OFF
1: RPM (Engine over-revving) ON

rpm_value RPM value for each pulse.
current_rpm Current RPM reading
vss_value VSS value is total pulses for 1 kilometer.
rpm_on_tresh RPM for detecting RPM (Engine over-revving) ON state.
on_duration Duration in seconds that must elapse before RPM (Engine over-revving) state change is accepted.
rpm_off_tresh RPM for detecting RPM (Engine over-revving) OFF state.
off_duration Duration in seconds that must elapse before RPM (Engine over-revving) state change is accepted.
fuel_cons Fuel Consumption l/h or km/l
eng_boost_pressure Engine Turbocharger Boost Pressure kPa
intake_manifold_temp Engine Intake Manifold 1 Temperature °C
eng_load OBD Calculated engine load %
accel_pos Accelerator pedal %
trottle_pos Throttle Position %
cargo_weight Cargo Weight N
brake_app_pressure Brake Application Pressure kPa
brake_pressure1 Brake Primary Pressure kPa
brake_pressure2 Brake Secondary Pressure kPa
brake_times Brake Switch apply times
clutch_times Clutch Switch apply times
cruise_time Time Cruise active second
abs_time Time ABS Active second
parking_brake Parking Brake Switch Status 0/1
intake_air_temp OBD Intake air temperature °C
trootle_pos OBD Throttle position %
mil_on_status OBD MIL ON (Engine Fault) Status 0/1
maf_air_rate OBD MAF air flow rate g/s
axle1-4 Axle weight kg
intake_manifold_air_temp Engine Intake Manifold 1 Temperature °C
pt_air_pressure Parking and/or Trailer Air Pressure kPa
brake_pressure1-2 Service Brake Air Pressure Circuit 1-2 kPa
drivers_state Driver1/2 Working State
driver1-2_card Driver1-2 Card status & time related state
tachograph_status Tachograph Overspeed status
tacho_ext_info Direction, Tachograph performance, handling info, system event
cango_ CANGO FMS parameter
gps_tm GPS Time. Unix Timestamp s
rtc_tm RTC Time. Unix Timestamp s
snd_tm Position Sending Time. Unix Timestamp s
prf Message prefix
jo1_cruise_ctrl

Cruise control is switched:
0 - switched off
1 - switched on

jo1_brake_switch

The switch signal indicates that the driver operated brake foot pedal is being pressed:
0 - pedal released
1 - pedal depressed

jo1_clutch_switch

The switch signal indicates that the clutch pedal is being pressed:
0 - pedal released
1 - pedal depressed

jo2_pto_state

This parameter indicates the current state of operation by the power takeoff device. PTO state:
0 = off/disabled
5 = Set
31 = not available

jo3 Accelerator Pedal Position %
jo4 Engine Percent Load At Current Speed 1 %
jo5 Fuel Level %
jo6_diagn_sup

FMS-standart Diagnostics Support:
0 - diagnostics is not supported
1 - diagnostics is supported
3 - don´t care


jo6_req_sup

FMS-standard Requests Support:
0 - request is not supported
1 - request is supported
3 - don´t care

jo7_drv1_state

Driver 1 working state
0 - Rest
1 - Driver available
2 - Work
3 - Drive
6 - Error
7 - not available

jo7_drv2_state

Driver 2 working state
0 - Rest
1 - Driver available
2 - Work
3 - Drive
6 - Error
7 - not available

jo7_motion

Indicating whether motion of the vehicle is detected:
0 - Vehicle motion not detected.
1 - Vehicle motion detected.

jo8_drv1_tm_st

Driver 1 time rel states. Indicating whether the driver approaches or exceeds working time limits (or other limits):
0 - normal
1 - 15 min bef. 4 ½ h
2 - 4 ½ h reached
3 - 15 min bef. 9 h
4 - 9 h reached
5 - 15 min bef. 16 h
6 - 16h reached
14 - Error
15 - not available


jo8_drv1_card_prs

Driver 1 card. Indicating the presence of a driver card:
0 - Card not present.
1 - Card present.

jo8_overspeed

Vehicle Overspeed. Indicating whether the vehicle is exceeding the legal speed limit set in the tachograph:
0 - No overspeed.
1 - Overspeed.

jo9_drv2_tm_st

Driver 2 time rel. states. Indicating whether the driver approaches or exceeds working time limits:
0 - normal
1 - 15 min bef. 4 ½ h
2 - 4 ½ h reached
3 - 15 min before 9 h
4 - 9 h reached
5 - 15 min bef. 16 h
6 - 16h reached
14 - Error
15 - not available


jo9_drv2_card_prs

Driver 2 card:
0 - Card not present.
1 - Card present.

jo10_sys_event

System event:
0 - no tachogr. Event.
1 - tachogr. Event.

jo10_info

Handling information:
0 - no handling information.
1 - handling information.

jo10_tach_perf

Tachgraph performance:
0 - Normal performance.
1 - Performance analysis.

jo10_direction

Direction indicator:
0 - Forward.
1 = Reverse.

jo11 Engine Coolant Temperature °C
j12

At least one PTO engaged:
0 - No PTO drive is engaged.
1 - At least one PTO drive is engaged.
2 - Error.
3 - Not available

jh1 Wheel based speed km/h
jh2 Engine Speed rpm
jh3 Axel weight 0 kg
jh4 Axel weight 1 kg
jh5 Axel weight 2 kg
jh6 Axel weight 3 kg
jh7 Axel weight 4 kg
jh8 Service distance km
jh9 Tachogr. vehicle speed km/h
jh10 Ambient Air Temperature °C
jh11 Fuel Rate L/h
jh12 Instantaneous Fuel Economy km/L
jl1 Engine total fuel used L
jl2 Engine total hours of Operation h
jl3

High resolution total vehicle distance.
*Value depends on firmware version.

jl4 High resolution engine total fuel used L
js1 Vehicle identification number
js2 FMS-standard SW-version supported
js3 Driver 1 identification
js4 Driver 2 identification
cd SIM CID
cell_id Current Cell ID
cm IMSI
mcc Current MCC
mnc Current MNC
gn 10Hz G sensor data
report_id Report ID
odometer Odometer km
hdop GPS HDOP
lac Current Cell LAC
me IMEI
rx_level Current RXLEV
pd Pending code status
ia Intake air temperature
inN Input Status with input number N
mp Manifold absolute pressure
outN Output status of output with number N
adc1 Analog Input Value
temp1 First Temperature Sensor Value °C
temp2 Second Temperature Sensor Value °C

Otros dispositivos del fabricante

Contacte con Wialon y logre los objetivos más ambiciosos con la telemática

Por favor, llene la solicitud para iniciar el trabajo con Wialon

Paso 1
Paso 2
Paso 3
Nombre y apellido*
Compañía*
Email*
Teléfono