| cam_num |
Total number of cameras that this
device supports |
|
| cam_status |
Bitwise parameter of cameras connected status.
bit1 - 1 indicates Camera 1 is connected;
0 indicates Camera 1 is disconnected;
...
bit64 - indicates Camera 64 status
|
|
| time_start |
Start time
|
|
| time_end |
End time
|
|
| alarm_flag8 |
Alert event code Bytes 0–5: reserved Bytes 6–7: Correspond to Meitrack's event codes, big-endian
|
|
| av_type |
Audio and video resource type 0: Audio and video 1: Audio 2: Video 3: Video, or audio and video
|
|
| stream_type |
Bitrate type 0: All streams 1: Major stream 2: Minor stream
|
|
| cap_type |
Memory type 0: All memories 1: Active memory 2: Standby memory
|
|
| file_length |
File size. Unit: byte, big-endian
|
|
| video_uri |
Video URI
|
|
| video_type |
Video type
|
|
| ftp_upload_percent |
Uploading progress percentage. Value
range: 0–100.
|
|
| ftp_filename |
File name
|
|
| RFID |
RFID code |
|
| event_code |
Event Code |
|
| gps_valid |
GPS status |
|
| gsm_signal |
GSM signal |
|
| hdop |
Horizontal Dilution of Precision |
|
| mileage |
Total accumulated mileage |
km |
| run_time |
Total accumulated runtime |
|
| battery |
battery charge |
% |
| adc5 |
Voltage of external power supply * 100
|
V |
| fuel_percent |
Percentage of remain fuel |
% |
| temp_N |
Temperature sensor N value |
°C |
| wln_accel_max |
Maximum acceleration value |
g |
| wln_brk_max |
Maximum deceleration value |
g |
| lls_N_temp |
LLS fuel sensor N temperature
|
°C |
| lls_N_val |
LLS fuel sensor value
|
|
| lls_N_freq |
LLS fuel sensor frequency
|
|
| dr_f_status |
Driver fatigue alert:
- 01 - Mild fatigue
- 02 - Moderate fatigue
- 03 - Severe fatigue
- 04 - Distraction alert
- 05 - Absence alert
- 06 - On Phone Call alert
- 07 - Smoking alert
- 08 - Yawning alert
|
|
| mccN |
Mobile country code for SIM card in slot N
|
|
| mncN |
Mobile network code for SIM card in slot N
|
|
| lacN |
Local area code for SIM card in slot N
|
|
| cell_idN |
Cellular station identification for SIM card in slot N
|
|
| outputs_status |
Output status
|
|
| inputs_status |
Bits 0–31 correspond to status of input ports 1–31
|
|
| system_flag |
The data is available only when the GPRS event code is 35. Bit 0: Whether to modify the EEP2 parameter. When the parameter value is 1, the EEP2 parameter is modified.
Bit 1: Indicates the ACC status. When the parameter value is 1, the ACC is on.
Bit 2: Indicates the anti-theft status. When the parameter value is 1, the tracker is in the arming state.
Bit 3: Reserved.
Bit 4: Moving flag. When the parameter value is 1, the tracker is moving.
Bit 5: Whether to connect the external power
supply. When the parameter value is 1, the external power supply is connected.
Bit 6: Whether the tracker is charging. When the parameter value is 1, the tracker is charging.
Bit 7: Whether to enable the sleep mode. When the parameter value is 1, the sleep mode is enabled.
Bit 8: Whether to connect the FMS. When the parameter value is 1, the FMS is connected.
Bit 9: Whether to enable the FMS function. When the parameter value is 1, the function is enabled.
|
|
| netw_ver |
The version of the network being connected， 0x01 by default
|
|
| netw_type |
The type of network being connected， 0: No Network,
1: Mobile Network,
2:WIFI (Reserved),
3: LAN (Reserved)
|
|
| adc1-3 |
Analog input value * 100
|
V |
| adc4 |
Battery analog *100
|
V |
