User rating

(13 Votes)

Forum Discussion

Number of units

Features STaRLink AVL:
  • Blackbox
  • Built-in odometer
  • Voice calls
Supported in Wialon:
  • ADC sensors
  • CAN-bus support
  • Garmin support
  • Driver identification
  • Digital sensors
  • LBS
  • Communication via TCP

The following data should also be added to STaRLink AVL unit properties section of Wialon GPS tracking software:

Device type: STaRLink AVL
Unique ID: custom

Specify the following parameters in configuration software or configuration STaRLink AVL for use in Wialon Hosting:

Server IP Address:
Server port: 20220

2791 units of STaRLink AVL device type are connected to Wialon Data Center. This represents 0.53% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name Description Units
destination The selected drive destination
drv Driving state (0 = Stopped, 1 = Driving)
eng Engine state (0 = Off, 1 = On)
event_code Event code
event_descr Event description
fix_type The GPS fix type for the current location (2D / 3D)
fw_ver The unit's firmware version
gssn The current average signal level of visible satellites
gss The average GPS satellite signal level
ibutton The currently attached Dallas iButton
ign Ignition state
immobilizer The immobilizer armed state (0 = Disarmed, 1 = Armed)
jam Jamming detection state (0 = Not jammed, 1 = Jammed)
odometer Current odometer value
paramN Extra parameter (N - number of parameter)
pwr_ext Vehicle battery voltage V
pwr_int Backup battery voltage V
report_reason Location report reason
satn The current number of visible satellites
sat The number of visible GPS satellites at the time the location was received
serial_num The unit's factory serial number
tempN_state Temperature sensor N state
tempN Temperature sensor N value
efuel_event Fuel message type
efuel_current Current fuel value exist in car L
efuel_tank_size Car's fuel tank size
efuel_current_prct Percentage fuel level exist in car %
efuel_value Current fuel litters or percentage
grmn_connected Garmin connection status: 0 = disconnected, 1 = connected.
Parameter appears when connection status is changed
esafe_msg_type Message type from eSafe:
137 - Maneuver notification, will be transmitted as Drive rule occurred if enabled
143 - Accident notification, will be transmitted as Accident detected if enabled
144 - Drive status changed
145 - Too many events
146 - Bad installation
147 - Possible accident notification
esafe_maneuv_type The eSafe maneuver type:
1 - Acceleration
2 - Breaking
3 - Left turn
4 - Right turn
5 - Wide left turn
6 - Wide right turn
7 - Left turn while decelerating
8 - Left turn while accelerating
9 - Wide left turn while decelerating
10 - Wide left turn while accelerating
11 - Right turn while decelerating
12 - Right turn while accelerating
13 - Wide right turn while decelerating
14 - Wide right turn while accelerating
15 - Traffic circle
16 - Lane change
17 - Overtaking
18 - Speed bump
19 - Start of off-road driving
20 - End of off-road driving
esafe_maneuv_level The eSafe maneuver level:
1 - Low
2 - Medium
3 - High
esafe_maneuv_dur The eSafe maneuver duration ms
esafe_force_x The eSafe maximum g force detected in the X axis g
esafe_force_y The eSafe maximum g force detected in the Y axis g
esafe_force_z The eSafe maximum g force detected in the Z axis g
esafe_accident_direct The eSafe accident directions:
1 - Front
2 - Front left
3 - Front right
4 - Back
5 - Back left
6 - Back right
7 - Left
8 - Right
9 - Vehicle rolled over
esafe_driver_state The eSafe driver state:
0 - Normal
1 - Aggressive
2 - Dangerous
esafe_aggres_maneuvers The eSafe total number of aggressive maneuvers
esafe_danger_maneuvers The eSafe total number of dangerous maneuvers
esafe_num_maneuvers The eSafe total number of maneuvers
top_speedN The top speed with of speed limit rule number N km/h
top_speed_tmN The number of seconds the vehicle was above the speed limit with number N sec

To get the dynamic parameters of the message send the command 03,01,177

More devices from the manufacturer