GPS tracker Piccolo ST | Integrated with Wialon

The following data should also be added to Piccolo ST unit properties section of Wialon GPS tracking software :

Device type:	Piccolo ST
Unique ID:	serial

Specify the following parameters in configuration software or configuration Piccolo ST for use in Wialon Hosting :

Server port:

20318

4 units of Piccolo ST device type are connected to Wialon Data Center. This represents 0% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
mess_num	Message Sequence No
rep_type	Report type: For message #224 1 – sharp turn 4 – quick acceleration 5 – sudden (sharp) braking 7 – sharp lanes crossing (direction changing) 8 – vehicle tilt report For message #30 0 – Trip Start – 1st vehicle movement start after Engine On 1 – Current state – When data must be sent (PTO status changed, by time interval) 2 – Trip End – Engine turns off after vehicle movement 3 – Engine Idle Stage End – The Engine is turned off with no Vehicle movement since last Engine On 4 – Diagnostic report – Diagnostic code was reported by one of the JBus modules 6 – Response on Host request – As response on request For message #229 Report type 0: the tag state was changed o Report status = 1: the tag was connected to Piccolo Plus units o Report status = 0: the tag was disconnected from Piccolo Plus unit Report type 1: Periodic connected tag report. State data is bit masked value. The Report Status value bits mean the following: o Bit 1 (mask 0x01) – the information is sent due to timeout expired o Bit 2 (mask 0x02) – the information is sent due to temperature changing o Bit 3 (mask 0x04) – the information is sent due to A2D value changing o Bit 4 (mask 0x08) – the information is sent due to Input changing Report type 2: Current tag state sent on Host request o Status = 0: the tag is not connected o Status = 1: the tag is connected Report type 3: the report includes the list of connected (active) tags, o Is sent as an answer on Host “Rescan active Tags” or “Get Active Tags list” message. When configured this report is sent when any available input state has changed. o Status field must be ignore
trip_state	Trip state: 0 – Unknown – The vehicle state was not detected yet 1 – Engine Off – The vehicle engine is off 2 – Engine starter is On – The engine is starting 3 – Engine On – Engine On (was successfully started), but did not move yet 4 – On Route – Engine On, and vehicle was moved since last Engine On
jbus_type	JBus Type
engien_speed	Current Engine speed, in 0.25 (implemented in Firmware version 1.85 and later)
engine_load	Current Engine load, in 0.5% (implemented in Firmware version 1.85 and later)
fuel_used	Total fuel Used, in 0.5 liters
coolant_temp	Coolant temperature
engine_on_tm	Time since engine on, s (FW 2.103 and later)
distance_till_service	Distance till next service (FW version2.99 and later)
сard#_info	Driver #1 and #2 information (FW 2.99 and later). Card info (SPN 1615 and 1616): may has one of following values: ƒ 0 = Card not present ƒ 1= Card present ƒ 2 = Card Error ƒ 3 = Information is not available
driver#_state	Driver #1 and #2 information (FW 2.99 and later) o Driver work state (SPN 1612 and 1613) value means the following: ƒ 0 = Rest - Sleeping ƒ 1 = Driver available – short break ƒ 2 = Work – Loading,. Unloading etc. ƒ 3 = Drive – behind wheel ƒ 6 = Error ƒ 7 = information is not available
driver#_state_tm	Driver #1 and #2 information (FW 2.99 and later) o Driver time related state (SPN 1617 and 1618) value means the following: ƒ 0 = Normal ( no limits reached) ƒ 1 = Limit #1- 15 min before 41⁄2 hours ƒ 2 = Limit #2 - 41⁄2 hours reached ƒ 3 = Limit #3 - 15 min before 9 hours ƒ 4 = Limit #4 - 9 hours reached ƒ 5 = Limit #5 - 15 min before 16 hours ƒ 6 = Limit #6 - 16 hours reached ƒ 14 = Error ƒ 15 = information is not available
parking_state	Parking brake state
idle_tm	Full idle time since engine on, s (FW 2.103 and later)
idle_tm_park	Idle time with parking brake on since engine on, s (FW 2.103 and later)
engine_tm	Engine total time of operation (FW 2.111 and later)
activ_tag_num	No. Of Active tags
report_type	Report Type (10.3.1 WLI RF Tag Report message, message type 229 (0xE5))
report_status_data	Report status data
tag_life_time	Tag life time
link_quality	Link Quality
battery_voltage	Battery voltage	mV
a2d_input	A2D input value	mV
di_state	Digital Inputs state
temp	Temperature, in 0.1 of degree
gps_data_flag	GPS Data Format Flag
int_temp	Internal Temperature
pwr_int	Internal battery voltage	V
pwr_ext	external power voltage	V
ext_temp	external temperature sensor	C
msg_type	Message Type: 10 - Emergency (alarm) Message 30 - J1587/J1708 Service Messages 201 - GPS Information Message 203 - IO States Report Message 224 - Acceleration alarm message 226 - Hardware Information message 228 - “No Valid GPS Fix” message 229 - WLI RF Tag Report message 248 - In Coverage Message 251 - Low Battery Message 252 - Acknowledgement Message 253 - Logout Message 254 - Login Message
mileage	Vehicle total distance	in 0.1 miles

Parameter name

Description

Units

mess_num

Message Sequence No

rep_type

Report type:

For message #224

1 – sharp turn
4 – quick acceleration
5 – sudden (sharp) braking
7 – sharp lanes crossing (direction changing)
8 – vehicle tilt report

For message #30

0 – Trip Start – 1st vehicle movement start after Engine On
1 – Current state – When data must be sent (PTO status changed, by time interval)
2 – Trip End – Engine turns off after vehicle movement
3 – Engine Idle Stage End – The Engine is turned off with no Vehicle movement since last Engine On
4 – Diagnostic report – Diagnostic code was reported by one of the JBus modules
6 – Response on Host request – As response on request

For message #229

Report type 0: the tag state was changed
o Report status = 1: the tag was connected to Piccolo Plus units
o Report status = 0: the tag was disconnected from Piccolo Plus unit
Report type 1: Periodic connected tag report. State data is bit masked value. The Report
Status value bits mean the following:
o Bit 1 (mask 0x01) – the information is sent due to timeout expired
o Bit 2 (mask 0x02) – the information is sent due to temperature changing
o Bit 3 (mask 0x04) – the information is sent due to A2D value changing
o Bit 4 (mask 0x08) – the information is sent due to Input changing
Report type 2: Current tag state sent on Host request
o Status = 0: the tag is not connected
o Status = 1: the tag is connected
Report type 3: the report includes the list of connected (active) tags,
o Is sent as an answer on Host “Rescan active Tags” or “Get Active Tags list” message. When configured this report is sent when any available input state has changed.
o Status field must be ignore

trip_state

Trip state:

0 – Unknown – The vehicle state was not detected yet
1 – Engine Off – The vehicle engine is off
2 – Engine starter is On – The engine is starting
3 – Engine On – Engine On (was successfully started), but did not move yet
4 – On Route – Engine On, and vehicle was moved since last Engine On

jbus_type

JBus Type

engien_speed

Current Engine speed, in 0.25 (implemented in Firmware version 1.85 and later)

engine_load

Current Engine load, in 0.5% (implemented in Firmware version 1.85 and later)

fuel_used

Total fuel Used, in 0.5 liters

coolant_temp

Coolant temperature

engine_on_tm

Time since engine on, s (FW 2.103 and later)

distance_till_service

Distance till next service (FW version2.99 and later)

сard#_info

Driver #1 and #2 information (FW 2.99 and later).
Card info (SPN 1615 and 1616): may has one of following values:
ƒ 0 = Card not present
ƒ 1= Card present
ƒ 2 = Card Error
ƒ 3 = Information is not available

driver#_state

Driver #1 and #2 information (FW 2.99 and later)
o Driver work state (SPN 1612 and 1613) value means the following:
ƒ 0 = Rest - Sleeping
ƒ 1 = Driver available – short break
ƒ 2 = Work – Loading,. Unloading etc.
ƒ 3 = Drive – behind wheel
ƒ 6 = Error
ƒ 7 = information is not available

driver#_state_tm

Driver #1 and #2 information (FW 2.99 and later)
o Driver time related state (SPN 1617 and 1618) value means the following:
ƒ 0 = Normal ( no limits reached)
ƒ 1 = Limit #1- 15 min before 41⁄2 hours
ƒ 2 = Limit #2 - 41⁄2 hours reached
ƒ 3 = Limit #3 - 15 min before 9 hours
ƒ 4 = Limit #4 - 9 hours reached
ƒ 5 = Limit #5 - 15 min before 16 hours
ƒ 6 = Limit #6 - 16 hours reached
ƒ 14 = Error
ƒ 15 = information is not available

parking_state

Parking brake state

idle_tm

Full idle time since engine on, s (FW 2.103 and later)

idle_tm_park

Idle time with parking brake on since engine on, s (FW 2.103 and later)

engine_tm

Engine total time of operation (FW 2.111 and later)

activ_tag_num

No. Of Active tags

report_type

Report Type (10.3.1 WLI RF Tag Report message, message type 229 (0xE5))

report_status_data

Report status data

tag_life_time

Tag life time

link_quality

Link Quality

battery_voltage

Battery voltage

a2d_input

A2D input value

di_state

Digital Inputs state

temp

Temperature, in 0.1 of degree

gps_data_flag

GPS Data Format Flag

int_temp

Internal Temperature

pwr_int

Internal battery voltage

pwr_ext

external power voltage

ext_temp

external temperature sensor

msg_type

Message Type:

10 - Emergency (alarm) Message

30 - J1587/J1708 Service Messages

201 - GPS Information Message

203 - IO States Report Message

224 - Acceleration alarm message

226 - Hardware Information message

228 - “No Valid GPS Fix” message

229 - WLI RF Tag Report message

248 - In Coverage Message

251 - Low Battery Message

252 - Acknowledgement Message

253 - Logout Message

254 - Login Message

mileage

Vehicle total distance

in 0.1 miles

Fill out a request form to get started with Wialon

Products

Niche products for addressing specific tasks

Piccolo ST

Contact Wialon and achieve the most ambitious goals with telematics

Become a partner

Request Wialon in your region

Fill out a request form to get started with Wialon