Meitrack T622G

Meitrack T622G
Manufacturer: Meitrack
Forum Discussion

Number of units

2
Online
51
Total
Features Meitrack T622G:
  • 3G
  • Blackbox

The following data should also be added to Meitrack T622G unit properties section of Wialon GPS tracking software:

Device type: Meitrack T622G
Unique ID: imei

Specify the following parameters in configuration software or configuration Meitrack T622G for use in Wialon Hosting:

Server port: 22050

51 units of Meitrack T622G device type are connected to Wialon Data Center. This represents 0% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name Description Units
RFID RFID code
event_type Event Code
valid GPS status
gsm_signal GSM signal
hdop Horizontal Dilution of Precision
mileage Total accumulated mileage km
engine_hours Total accumulated runtime
battery battery charge V
pwr_ext Voltage of external power supply V
fuel_percent Percentage of remain fuel %
temp_N Temperature sensor N value °C
wln_accel_max Maximum acceleration value g
wln_brk_max Maximum deceleration value g
lls_N_temp LLS fuel sensor N temperature
°C
lls_N_val LLS fuel sensor value
lls_N_freq LLS fuel sensor frequency
dr_f_status Driver fatigue alert:
  • 01 - Mild fatigue
  • 02 - Moderate fatigue
  • 03 - Severe fatigue
  • 04 - Distraction alert
  • 05 - Absence alert
  • 06 - On Phone Call alert
  • 07 - Smoking alert
  • 08 - Yawning alert
ignition Ignition status
tire{tire_id}_loc Tire position
Tire position:7~5bit indicate the vehicle head or trailer:000(B): Vehicle head, 001(B):Trailer 1,010(B): Trailer 2, 011(B): Trailer 3,100(B): Trailer 4, 4~0bit indicate the tire number:For example, 00001(B), indicating the first tire
tire{tire_id}_press Tire pressure value:
Formula :obtained value x 0.025
bar
tire{tire_id}_temp Tire temperature value:
Formula: obtained value – 50
°C​
tire{tire_id}_alert Tire status:
Bit7: indicates the battery voltage status of the transmitter. 0: normal voltage; 1: low voltage.
Bit6:Whether to receive data from the transmitter. If you do not receive data from the transmitter within 15 minutes, the parameter value will be reset to 1. Bit5:reserved.
Bit4:When the value is 1, the air pressure is high.
Bit3:When the value is 1, the air pressure is low
Bit2:indicates temperature status. 1: high temperature; 0: normal temperature.
Bit1~Bit0:indicates the alert status. 00: no alert; 01: fast air leak alert; 10: slow air leak alert; 11: tire inflation alert.
system_flag System Flag:
Bit 0: Whether to modify the EEP2 parameter. When the parameter value is 1, the EEP2 parameter is modified.
Bit 1: Indicates the ACC status. When the parameter value is 1, the ACC is on. Bit 2: Indicates the anti-theft status. When the parameter value is 1, the tracker is in the arming state.
Bit 3: vibration flag. When the parameter value is 1, the tracker is vibrating.
Bit 4: moving flag. When the parameter value is 1, the tracker is moving.
Bit 5: Whether to connect the external power supply. When the parameter value is 1, the external power supply is connected.
Bit 6: Whether the tracker is charging. When the parameter value is 1, the tracker is charging.
Bit 7: Whether to enable the sleep mode. When the parameter value is 1, the sleep mode is enabled.
Bit 8: Whether to connect the FMS. When the parameter value is 1, the FMS is connected.
Bit 9: Whether to enable the FMS function. When the parameter value is 1, the function is enabled.
Bit 10: Whether to connect the Mobileye. When the parameter value is 1, the Mobileye is disconnected.
Bit 11: Whether to connect the Mobileye. When the parameter value is 1, the Mobileye is connected.
Bits 12–31: reserved.
outputs_status Indicates the status values of eight output ports. Bits 0–7 correspond to status of output ports 1–8.
inputs_status Indicates the status values of eight Input ports. Bits 0–7 correspond to status of Input ports 1– 8.
geo_fance_number Number of Geo-fence
clutch_switch Clutch switch:
0: The clutch pedal is released
1: The clutch pedal is pressed.
park_brake Parking brake switch:
0: Do not apply the brake.
1: Apply the brake.

cruise_cnt Cruise control system:
0: The cruise control system is switched off.
1: The cruise control system is switched on.
acc_pedal Accelerator pedal position %
can_fuel_lvl CAN bus fuel level %
fuel_level_proc Fuel level, should be divided by 100 %
veh_speed_taho Vehicle speed (based on the tachograph) km/h
veh_speed_wheel Vehicle speed (based on the wheel) km/h
engine_speed Engine speed rpm
eng_cool_temp Engine coolant temperature °C
run_time Run time h
total_fuel_cons Total fuel consumption l
total_eng_run_tm Total engine run time h
high_res_veh_dist High resolution vehicle distance m
service_dist Service distance km
axle_weight Axle weight kg
sens{ind_sens} Temperature sensor {ind_sens} value °C
accel_x Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered mg
accel_y Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered mg
accel_z Indicates the instantaneous acceleration of the XYZ axis when a crash alarm is triggered mg

More devices from the manufacturer

News

Fill out a request form to get started with Wialon

Step 1
Step 2
Step 3
First and last name*
Company*
Email*
Phone