Cellocator CR300

Manufacturer: Pointer Telocation

Forum Discussion

Number of units

3421

Online

5907

Total

Information
Parameters

Features Cellocator CR300:

3G
Blackbox

Supported in Wialon:

Accelerometer
ADC sensors
CAN-bus support
Remote management via GPRS
Driver identification
Digital sensors
LBS
SMS sending of data
Communication via TCP

The following data should also be added to Cellocator CR300 unit properties section of Wialon GPS tracking software :

Device type:	Cellocator CR300
Unique ID:	serial

Specify the following parameters in configuration software or configuration Cellocator CR300 for use in Wialon Hosting :

Server port:

21269

5907 units of Cellocator CR300 device type are connected to Wialon Data Center. This represents 0.25% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name

Description

Units

adc

Analog input sensor

mcc

Mobile Country Code

mnc

Mobile Network Code

lac

Location Area Code

cell_id

cell ID

flag

Current GSM Operator (2 nd and 3 rd Nibbles)

unit_status

0 bit - Communication with GPS is 1 - available / 0 - not available
1 bit - Network (0 - Home, 1 - Roam)
2 bit - Correct Time (1 - Invalid/estimated time stamp, 0 – Valid time stamp)
3 bit - Source of Speed (0 – GPS, 1 – Pulse frequency input)

reason

Transmission Reason Specific Data

reason_data

Transmission Reason

pwr_int

The voltage on the internal battery

pwr_ext

External power supply voltage

services

Bit 0 - Actual GNSS antenna selected (0 – Internal, 1 – External). (Relevant only for Cello GNSS variants)
Bit 1 - Trailer status indication. (0 – Trailer Disconnected, 1 – Trailer
Connected)

Bit 2 - 4 - CFE Type.

Bit 4	Bit 3	Bit 2	CFE Type
0	0	0	Not Applicable (Legacy state)
0	0	1	CFE is not connected
0	1	0	CFE BT is connected
0	1	1	CFE Basic is connected
1	0	0	CFE I/O is connected
1	0	1	CFE premium is connected
1	1	1	Undefined CFE Type

unit_mode

Unit Mode of Operation. The functioning of the unit can be generalized as a finite state machine model, with a few "stages" of operation. The "current stage" is referred to as "unit mode", or "mode of operation", as following:

Value Unit Mode Description
0x00 Standby Engine On
0x01 Standby Engine Off
0x02 Passive Arming (for security modifications)
0x03 Pre-Arming (for security modifications)
0x04 Alarm Armed (for security modifications)
0x05 Silent Delay (for security modifications)
0x07 Alarm Triggered (for security modifications)
0x0E Garage Mode
0x0F Transmissions Delay (for FW versions older than 25)
0x10 Towed mode (same as Standby Engine On, but with ignition off)

mode1, mode2

MODE 1 and Mode 2
These fields are generated by the GPS and transparently monitored in the outgoing message from the unit. The fields define the validity of GPS data in the message. The unit considers the valid fix according to the "Enable Tight GPS PMODE Filter" parameter (address 509, bit 7):
 If "Enable Tight GPS PMODE Filter" is enabled, the unit considers the GPS data as valid only if Mode 1 = 3 or 4 AND Mode 2 = 2
 If "Enable Tight GPS PMODE Filter" is disabled, the unit considers the GPS data as valid only if Mode 1 =2, 3, 4, 5 and 6

odom

Mileage Counter (Odometer)