GPS tracker Queclink GV55 | Integrated with Wialon

Features Queclink GV55:

Blackbox

Supported in Wialon:

ECO driving
Remote management via GPRS
Digital sensors
LBS
Remote management via SMS
Communication via TCP

Can be supported upon request:

SMS sending of data
Communication via UDP

The following data should also be added to Queclink GV55 unit properties section of Wialon GPS tracking software :

Device type:	Queclink GV55
Unique ID:	imei

Specify the following parameters in configuration software or configuration Queclink GV55 for use in Wialon Hosting :

Server port:

20979

8467 units of Queclink GV55 device type are connected to Wialon Data Center. This represents 0.36% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name	Description	Units
report_type	Report Type
rep_id	Report ID
rep_type	Report type (GT###)
mcc	Mobile country code
mnc	Mobile network code
lac	Location area code in hex format
cell_id	Cell ID in hex format
mileage	The current total mileage
hour_meter_count	Hour Meter Count	h
h_m_count	Hour Meter Count	h
battery	Backup Battery Percentage	%
ign	Ignition status
motion_state	Device status 16 (Tow): The device attached vehicle is ignition off and it is towed. 1A (Fake Tow): The device attached vehicle is ignition off and it might be towed. 11 (Ignition Off Rest): The device attached vehicle is ignition off and it is motionless. 12 (Ignition Off Motion): The device attached vehicle is ignition off and it is moving before it is treated as being towed. 21 (Ignition On Rest): The device attached vehicle is ignition on and it is motion less 22 (Ignition On Motion): The device attached vehicle is ignition on and it is moving 41 (Sensor Rest): The device attached vehicle is motionless without ignition signal detected 42 (Sensor Motion): The device attached vehicle is moving without ignition signal detected
pwr_ext	External Power Voltage
iccid	ICCID
csq_rssi	GSM signal level of the terminal
gsm	GSM signal level of the terminal
csq_ber	The quality of the GSM signal. The range is 0-7, 99 for unknown.
bat_status	Whether the external power supply is connected. 0: Not connected 1: Connected
charging	Whether the backup battery is charging when the main power supply is connected. 0: Not charging 1: Charging
led_on	Indicate whether the LED’s are turned on: 0: Off 1:On
din_status	A bitwise hex integer to represents the logical status of the digital input. From the lowest bit to the highest bit, each bit represents ignition detection and one of the digital inputs 1 respectively. For each bit, 0 means disable status, 1 means enable status.
dout_status	A bitwise hex integer to represents the logical status of the digital output. From the lowest bit to the highest bit, each bit represents one of the digital outputs 1 – 2 respectively. For each bit, 0 means disable status, 1 means enable status
time_zone	The time offset of the local time zone to the UTC time.	m
daylight_saving	The current setting of the daylight saving. 0: Daylight saving is disabled 1: Daylight saving is enabled
data_type	The data reported to backend server is recorded before or after crash. 0: before crash. 1: after crash.
frames_count	Total number of messages that are sent to the bckend server for the crash event.
frame	A numeric to indicate the sequence of the current message.
x_axis#	X axis acceleration data
y_axis#	Y axis acceleration data
z_axis#	Z axis acceleration data
ign_off_duration	Duration of Ignition Off	s
ign_on_duration	Duration of Ignition On	s
state	The current motion state when the vehicle leaves idling status.
idle_dt	The time that the vehicle has been in idling status.	s
gps_signal_status	GPS Signal Status: 0 means lost GPS signal or no successful GPS fix, 1 means GPS signal recovered and successful GPS fix.
sats	Satellite Number
wave1_out_id	ID of the output With wave shape 1
wave1_out_active	The output status with wave shape 1
roaming_state	Roam state : 0 Home 1 Known Roaming 2 Unknow Roaming 3 Blocking Report
jamming_status	The current Jamming status of the device. 1: Quit the jamming. 2: Enter the jamming.
jamming_cw	Continuous wave(narrowband) jamming detection threshold	dB
jamming_gps	Broadband jamming detection threshold	dB
is_pwr_ext	External Power Supply
mcu_ver	MCU Version
hw_ver	Hardware Version
fw_ver	Firmware Version