Arnavi

Arnavi
Manufacturer: Arusnavi
Forum Discussion

Number of units

43949
Online
74519
Total
Features Arnavi:
  • 2G
  • 3G
  • 4G/LTE
  • Blackbox
  • BLE enabled
  • Dual SIM
  • GLONASS support
  • Magnetic mounting
  • Sending data to multiple servers
  • Built-in odometer
  • Voice calls
Supported in Wialon:
  • Accelerometer
  • ADC sensors
  • Camera connection
  • CAN-bus support
  • ECO driving
  • Remote management via GPRS
  • Driver identification
  • Digital sensors
  • LBS
  • Remote management via SMS
  • Alarm button
  • Tachograph file download
  • Communication via TCP

The following data should also be added to Arnavi unit properties section of Wialon GPS tracking software :

Device type: Arnavi
Unique ID: imei

Specify the following parameters in configuration software or configuration Arnavi for use in Wialon Hosting :

Server port: 20623

74519 units of Arnavi device type are connected to Wialon Data Center. This represents 3.17% of all AVL Hardware connected.

Below chart represents the dynamic of connections in the last 30 days:

Parameter name Description Units
counterX Counter on a digital input, X - number of inputs
adcX

Analog sensor, X - number of sensor

temp_ext External temperature sensor
fsdata Fuel sensor data
accel_stop Accelerometer status, 0 - movement 1 - Parking
pwr_ext Value of external voltage (ARNAVI 4 / ARNAVI 5 / INTEGRAL) Battery voltage (BEACON) Volt
pwr_int Value of internal battery voltage (ARNAVI 4 / ARNAVI 5 / INTEGRAL) Voltage of CPU (BEACON) Volt
ant_state GPS antenna status
ign Ignition status
acc_x X-axis acceleration

M/S2

acc_y Y-axis acceleration

M/S2

acc_z Z-axis acceleration

M/S2

temp_int Internal temperature sensor
uptime Time since last start/reboot
reboot Reason of the last reboot
iccid ICCID SIM card
imei IMEI GSM-module
pin Physical input value (Arnavi 5) bitwise parameter control
v_in Virtual input value (Arnavi 5)
hdop Horizontal Dilution of Precision (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
cell_id Cell code GSM (ARNAVI 4 / ARNAVI 5 / INTEGRAL / BEACON)
lac (ARNAVI 4 / ARNAVI 5 / INTEGRAL / BEACON)
mnc (ARNAVI 4 / ARNAVI 5 / INTEGRAL / BEACON)
mcc (ARNAVI 4 / ARNAVI 5 / INTEGRAL / BEACON)
gsm

GSM signal level
From 1 to 31
(99 – no GSM signal)
(ARNAVI 4 / ARNAVI 5 / INTEGRAL / BEACON)

gsm_st

GSM chip state
Duplicate of lightings (0 – not enabled, 1 – started, 2 – GPRS test, 3 – Connected to server (ARNAVI 4 / INTEGRAL))
Duplicate of lightings (0 – not enabled, 1 – enabled, 2 – AT Ok, network search, 3 – GPRS test, 4 – GPRS OK (ARNAVI 5))

nav_st Navigation chip state (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
mw Move state (ARNAVI 4 / ARNAVI 5 / INTEGRAL) 0 – not move, 1 – move
sim_t Number of sim card, uses now for connection (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
sim_in SIM inserted (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
st0 Opencase sensor (ARNAVI 4 / INTEGRAL) Optional
st1 1-wire discrete state (ARNAVI 4 / INTEGRAL)
st2 Ignition (ARNAVI 4 / INTEGRAL) Read from IN2 (or from CAN)
freq_x Frequency sensor, X - number of input. (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
info_messages

Special value (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
Rule for create new package
Time for next wakeup (unix-time) (BEACON)

lls1_val RS485 value (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
lls1_temp RS485 temperature (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
I/O

Bitwise parameter (ARNAVI 4 / INTEGRAL)
in1, in2, in3, in4, in5, in6
out1, out2, out3, out4

bitwise control
can_eng_full_time CAN engine hours (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
can_full_mileage CAN odometer (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
can_full_fuel_cons CAN fuel const (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
can_fuel_level CAN fuel level (%)(ARNAVI 4 / ARNAVI 5 / INTEGRAL) %
can_rpm CAN RPM (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
can_eng_temp CAN temp of engine (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
can_speed CAN speed (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
can_axle_load1 CAN load for axle 1 (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
sim1_st State of sim 1 (ARNAVI 5) 0 – no present, 2 – search network, 1 – home network, 5 - roaming
sim2_st State of sim 2 (ARNAVI 5) 0 – no present, 2 – search network, 1 – home network, 5 - roaming
s1_st State of server 1 (ARNAVI 5) 0 – not present in settings, 1 - connecting, 2 - connected
s2_st State of server 2 (ARNAVI 5) 0 – not present in settings, 1 - connecting, 2 - connected
os Opencase sensor state (ARNAVI 5) Optional
msd State of MicroSD (ARNAVI 5) 1 – inserted, 0 – not inserted
bt Bluetooth (ARNAVI 5) 1 – enable, 0 - disable
gps_full_mileage Odometer from GNSS (ARNAVI 4 / ARNAVI 5 / INTEGRAL)
hs Time of last settings change (BEACON)
balance_sim1 Balance of sim1
balance_sim2 Balance of sim2

You can also download an example of unit configuration file for Arnavi to be used in Wialon GPS tracking software. When creating an object, import this configuration file by selecting "Import from File" option. This way you will create a pre-configured object with some sensors. Do not forget to specify the unique Id of Your device.

More devices from the manufacturer

Contact Wialon and achieve the most ambitious goals with telematics

Fill out a request form to get started with Wialon

Step 1
Step 2
Step 3
First and last name*
Company*
Email*
Phone